Switch From Percussion To Cartridge By Changing Cylinders
Six-round conversion cylinder converts steel frame, cap and ball revolvers to modern centerfire. Patterned after an original Remington design for a drop-in fit. Cylinder and back plate fit together without screws. To reload, just drop the cylinder, pull the plate off and dump the fired cases. Use in steel frame guns only, with black powder equivalent loads. No FFL required to purchase. Models for .44 caliber, 1858 Remington Italian replicas, Uberti and Ruger® Old Army™ are chambered for the .45 Colt cartridge. Your bore should be slugged and verified to be capable of running a .451-452" diameter projectile by a qualified gunsmith. This is for STEEL frame 44 cal.only. NOT FOR BRASS FRAME REVOLVERS. For use with 'cowboy' loads only, nothing to exceed 750 to 800 ft. per second black powder loads up to 34 grains of FFG black powder or equivalent, for STEEL frame guns ONLY.
SPECS: Blued steel or stainless steel as indicated. May require fitting to base pin.
Mer...
Byt från slaghatt till patron genom att byta cylindrar
Sexskotts konverteringscylinder omvandlar stålram, slaghatt och kulpistoler till moderna centertända vapen. Mönstrad efter en originaldesign från Remington för en passform utan modifikation. Cylindern och bakplattan passar ihop utan skruvar. För att ladda om, bara släpp cylindern, dra av plattan och töm de avfyrade hylsorna. Används endast i stålramvapen, med laddningar motsvarande svartkrut. Ingen FFL krävs för att köpa. Modeller för .44 kaliber, 1858 Remington italienska replikor, Uberti och Ruger® Old Army™ är kamrade för .45 Colt patronen. Ditt vapen bör slugas och verifieras för att kunna hantera en projektil med en diameter på .451-452" av en kvalificerad vapensmed. Detta är för STÅLram 44 cal. endast. INTE FÖR MÄSSINGSRAMREVOLVRAR. Endast för användning med 'cowboy'-laddningar, inget som överstiger 750 till 800 fot per sekund svartkrutladdningar upp till 34 grains av FFG svartkrut eller motsvarande, för STÅLramvapen ENDAST.
SPECS: Blått stål eller rostfritt stål som angivet. Kan kräva anpassning till baspinnen.
Mer...
Kundernas betyg påTAYLORS AND CO. PIETTA, 1858 REM CONVERSION CYLINDER 44 TO 45LC
Antal betyg: 9
Från brownells.com: 9
Medelbetyg: 4,1
Conversion Cylinder for 1847 Walker(2018-02-14)
Ordered one of these for my Uberti 1847 Walker and so glad I did. This cylinder fits and functions perfectly and now allows me to shoot 45LC Cowboy Loads. Cleanup is obviously much easier than with black powder and much less smoke. Also, I think it is actually a bit quicker to load even though you have to practically disassemble the pistol. The price of these conversion cylinders may seem a bit high for just a cylinder, but trust me, they are very well worth the advantages you get, in my opinion.
needs to be fit by a gunsmith to work(2009-10-18)
this is not a drop in cylinder conversion. lots of work went into this conversion to make it fit. Gunsmithing is necessary!
Ruger Old Army Conversion(2012-01-21)
My experience was totally different. Literally dropped in just like the original. It is quite accurate with hand loads and the pistol can easily handle velocities up near 1000fps which is about 10% above cowboy loads. The Ruger Old Army is the only one I would push the load as it's so beefy and the converter shows no abnormal wear on the recoil shield after over 500 rds.
Be Warned!(2009-11-05)
A customer of mine purchased one of these cylinders and it spit out lead shavings to the sides with enough force to penetrate the skin at 10'(first hand testimony here!). When contacted, the company disclosed that this is a "common issue" with their conversion cylinders and that the revolver and cylinder must be returned to the company for repair. Having a gunsmith work on it will void the warranty. Don't recall reading this in their manual, however.
Perfect fit works as they say(2012-06-12)
This is a perfect solution to convert your Remington New Army .44 percussion to .45 Colt (LC), they typically drop in with no fitting required and are perfectly timed in a new or very well maintained pistol. Those that claim to have issues have a poorly maintained pistol or have no knowledge of this conversion process. The R&D Cylinders work as advertised and are great! I have several for my Remington New Army Pietta's and for my Ruger Old Army .45 Love them!
excellent product I love it(2014-12-03)
Well Done(2015-06-09)
This conversion fit nice and snug in my Peitta.
It is finished better than the original revolver.
It really shot well and I experienced no problems.
You will need to keep a rod or other item around to push some of the cases out after firing it a bunch depending on how dirty your ammo is.
The instructions say to limit the ammo to black powder pressures and you will need to follow that because the locking notches are right at the thinnest part of the cylinder.
The main drawback and the reason for 4 instead of 5 stars is that there are no safety notches like the original cylinder that the hammer could rest in.
I really like the look of the original cap and ball revolvers but black powder IS dirty and one doesn't always have time to clean right away.
Love this cylinder(2016-12-02)
I own 2 Pietta 1858 Remingtons and bought one of these for the target one and it is a pleasure to shoot and handle. I use the loading lever to puncture through the chamber's to eject the brass. It is a very good snug fit so care must be taken when inserting back into the gun.
Great Product!(2014-08-16)
The fit is factory tight with no filing, finish matches the Ruger Old Army SS and function of this product is perfect. When you get tired of cleaning BP you can switch to Smokeless powder and let the fun begin. I bought it out right for myself, Cowboy shooting.
Produktnr: 633185101 TAYLORS AND CO. PIETTA, 1858 REM CONVERSION CYLINDER 44 TO 45LC Tillverkarens produktnummer: P839665006207 Sexskotts konverteringscylinder omvandlar stålram, slaghatt och kulpistoler till moderna centertända vapen. Mönstrad efter en originaldesign från Remington för en passform utan modifikation. Cylindern och bakplattan passar ihop utan skruvar. För att ladda om, bara släpp cylindern, dra av plattan och töm de avfyrade hylsorna. Används endast i stålramvapen, med laddningar motsvarande svartkrut. Ingen FFL krävs för att köpa. Modeller för .44 kaliber, 1858 Remington italienska replikor, Uberti och Ruger® Old Army™ är kamrade för .45 Colt patronen. Ditt vapen bör slugas och verifieras för att kunna hantera en projektil med en diameter på .451-452" av en kvalificerad vapensmed. Detta är för STÅLram 44 cal. endast. INTE FÖR MÄSSINGSRAMREVOLVRAR. Endast för användning med 'cowboy'-laddningar, inget som överstiger 750 till 800 fot per sekund svartkrutladdningar upp till 34 grains av FFG svartkrut eller motsvarande, för STÅLramvapen ENDAST.
Tillstånd Krävs(Vid köp av högkapacitetsmagasin krävs licenskontroll. E-posta eller posta en kopia på din licens (båda sidor) och ID-handling.
Vid köp av licenspliktiga vapendelar krävs tillstånd - Handlartillstånd eller Inköpstillstånd (Handlartillstånd eller Inköpstillstånd från polisen måste postas till oss. Licenspliktiga vapendelar skickas inte förrän vi har erhållit tillståndet.))
Tillverkas i USA
USA: s exportklassificering: 0A501.c
Destination Control Statement: Dessa poster styrs av USA: s regering och godkänns endast för export till det land där den slutliga destinationen används av den slutliga mottagaren eller slutanvändaren som identifierats här. De får inte vidareförsäljas, överföras eller på annat sätt kasseras till något annat land eller någon annan än den godkända slutliga mottagaren eller slutanvändaren, antingen i sin ursprungliga form eller efter att ha monterats i andra föremål utan att först få godkännande från den amerikanska regeringen eller som annars är tillåten enligt amerikansk lag och förordningar.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Produktnr: 633000001 TAYLORS AND CO. RUGER® OLD ARMY™ CONVERSION CYLINDER, SS Tillverkarens produktnummer: NONE839665006313 Sexskotts konverteringscylinder omvandlar stålram, slaghatt och kulpistoler till moderna centertända vapen. Mönstrad efter en originaldesign från Remington för en passform utan modifikation. Cylindern och bakplattan passar ihop utan skruvar. För att ladda om, bara släpp cylindern, dra av plattan och töm de avfyrade hylsorna. Används endast i stålramvapen, med laddningar motsvarande svartkrut. Ingen FFL krävs för att köpa. Modeller för .44 kaliber, 1858 Remington italienska replikor, Uberti och Ruger® Old Army™ är kamrade för .45 Colt patronen. Ditt vapen bör slugas och verifieras för att kunna hantera en projektil med en diameter på .451-452" av en kvalificerad vapensmed. Detta är för STÅLram 44 cal. endast. INTE FÖR MÄSSINGSRAMREVOLVRAR. Endast för användning med 'cowboy'-laddningar, inget som överstiger 750 till 800 fot per sekund svartkrutladdningar upp till 34 grains av FFG svartkrut eller motsvarande, för STÅLramvapen ENDAST.
Switch From Percussion To Cartridge By Changing Cylinders
Six-round conversion cylinder converts steel frame, cap and ball revolvers to modern centerfire. Patterned after an original Remington design for a drop-in fit. Cylinder and back plate fit together without screws. To reload, just drop the cylinder, pull the plate off and dump the fired cases. Use in steel frame guns only, with black powder equivalent loads. No FFL required to purchase. Models for .44 caliber, 1858 Remington Italian replicas, Uberti and Ruger® Old Army™ are chambered for the .45 Colt cartridge. Your bore should be slugged and verified to be capable of running a .451-452" diameter projectile by a qualified gunsmith. This is for STEEL frame 44 cal.only. NOT FOR BRASS FRAME REVOLVERS. For use with 'cowboy' loads only, nothing to exceed 750 to 800 ft. per second black powder loads up to 34 grains of FFG black powder or equivalent, for STEEL frame guns ONLY.
SPECS: Blued steel or stainless steel as indicated. May require fitting to base pin.
Mer...
Byt från slaghatt till patron genom att byta cylindrar
Sexskotts konverteringscylinder omvandlar stålram, slaghatt och kulpistoler till moderna centertända vapen. Mönstrad efter en originaldesign från Remington för en passform utan modifikation. Cylindern och bakplattan passar ihop utan skruvar. För att ladda om, bara släpp cylindern, dra av plattan och töm de avfyrade hylsorna. Används endast i stålramvapen, med laddningar motsvarande svartkrut. Ingen FFL krävs för att köpa. Modeller för .44 kaliber, 1858 Remington italienska replikor, Uberti och Ruger® Old Army™ är kamrade för .45 Colt patronen. Ditt vapen bör slugas och verifieras för att kunna hantera en projektil med en diameter på .451-452" av en kvalificerad vapensmed. Detta är för STÅLram 44 cal. endast. INTE FÖR MÄSSINGSRAMREVOLVRAR. Endast för användning med 'cowboy'-laddningar, inget som överstiger 750 till 800 fot per sekund svartkrutladdningar upp till 34 grains av FFG svartkrut eller motsvarande, för STÅLramvapen ENDAST.
SPECS: Blått stål eller rostfritt stål som angivet. Kan kräva anpassning till baspinnen.
Mer...
Kundernas betyg påTAYLORS AND CO. PIETTA, 1858 REM CONVERSION CYLINDER 44 TO 45LC
Antal betyg: 9
Från brownells.com: 9
Medelbetyg: 4,1
Conversion Cylinder for 1847 Walker(2018-02-14)
Ordered one of these for my Uberti 1847 Walker and so glad I did. This cylinder fits and functions perfectly and now allows me to shoot 45LC Cowboy Loads. Cleanup is obviously much easier than with black powder and much less smoke. Also, I think it is actually a bit quicker to load even though you have to practically disassemble the pistol. The price of these conversion cylinders may seem a bit high for just a cylinder, but trust me, they are very well worth the advantages you get, in my opinion.
needs to be fit by a gunsmith to work(2009-10-18)
this is not a drop in cylinder conversion. lots of work went into this conversion to make it fit. Gunsmithing is necessary!
Ruger Old Army Conversion(2012-01-21)
My experience was totally different. Literally dropped in just like the original. It is quite accurate with hand loads and the pistol can easily handle velocities up near 1000fps which is about 10% above cowboy loads. The Ruger Old Army is the only one I would push the load as it's so beefy and the converter shows no abnormal wear on the recoil shield after over 500 rds.
Be Warned!(2009-11-05)
A customer of mine purchased one of these cylinders and it spit out lead shavings to the sides with enough force to penetrate the skin at 10'(first hand testimony here!). When contacted, the company disclosed that this is a "common issue" with their conversion cylinders and that the revolver and cylinder must be returned to the company for repair. Having a gunsmith work on it will void the warranty. Don't recall reading this in their manual, however.
Perfect fit works as they say(2012-06-12)
This is a perfect solution to convert your Remington New Army .44 percussion to .45 Colt (LC), they typically drop in with no fitting required and are perfectly timed in a new or very well maintained pistol. Those that claim to have issues have a poorly maintained pistol or have no knowledge of this conversion process. The R&D Cylinders work as advertised and are great! I have several for my Remington New Army Pietta's and for my Ruger Old Army .45 Love them!
excellent product I love it(2014-12-03)
Well Done(2015-06-09)
This conversion fit nice and snug in my Peitta.
It is finished better than the original revolver.
It really shot well and I experienced no problems.
You will need to keep a rod or other item around to push some of the cases out after firing it a bunch depending on how dirty your ammo is.
The instructions say to limit the ammo to black powder pressures and you will need to follow that because the locking notches are right at the thinnest part of the cylinder.
The main drawback and the reason for 4 instead of 5 stars is that there are no safety notches like the original cylinder that the hammer could rest in.
I really like the look of the original cap and ball revolvers but black powder IS dirty and one doesn't always have time to clean right away.
Love this cylinder(2016-12-02)
I own 2 Pietta 1858 Remingtons and bought one of these for the target one and it is a pleasure to shoot and handle. I use the loading lever to puncture through the chamber's to eject the brass. It is a very good snug fit so care must be taken when inserting back into the gun.
Great Product!(2014-08-16)
The fit is factory tight with no filing, finish matches the Ruger Old Army SS and function of this product is perfect. When you get tired of cleaning BP you can switch to Smokeless powder and let the fun begin. I bought it out right for myself, Cowboy shooting.