Varukorgen är tom.

Varukorg

Hjälp och kontakt

Fri frakt på beställningar över 2.999 kr

100 dagars returrätt

Nyhetsbrev

REA

TIMNEY
308 AR DROP-IN TRIGGER MODULE SOLID SHOE

081950006700 883000023

Obtain A Super-Smooth Pull & Crisp Letoff In Minutes

Self-contained module is ready to install in your small-pin AR and deliver an exceptionally smooth, crisp, creep-free single-stage trigger pull that feels more like a traditional bolt action than a combat rifle trigger. 100% drop-in—no gunsmithing, fitting, or adjusting required. All components are captive in the lightweight, aluminum alloy housing. Hammer is wire-EDM machined from S7 tool steel that combines hardness to resist wear with superior impact resistance to withstand heavy use without chipping or breaking. Other components are EDM cut from A2 tool steel, then heat treated to Rc 56-60 for long service life. Precision-ground engagement surfaces ensure superb reliability and a crisp, clean hammer release. Installs using your rifle’s original hammer/trigger pins; proprietary design eliminates pin walkout. AR-.308 model has a factory-set 4 lb. pull weight, a solid shoe, and more hammer mass to ensure positive ignition of harder .308/7.62mm primers.

SPECS: Hammer – S7 tool steel, natural color, Teflon-Nickel coated. Trigger/Internal Components - Hardened A2 tool steel, black oxide finish. Housing – 6061 T6 aluminum, gold anodized finish. Fits rifles with .154" diameter hammer/trigger pin holes. Will not fit Colt-manufactured AR-15s with sear block. AR-.308 – non-adjustable 4 lb. pull weight. Fits AR-style .308 rifles that accept small-pin AR-15 trigger components.

Mer...

Få Ett Supermjukt Avtryck & Skarpt Avsläpp På Minuter

Självständig modul är redo att installeras i din small-pin AR och leverera en exceptionellt mjuk, skarp, krypfri enstegs avtryckarupplevelse som känns mer som en traditionell repetergevär än en stridsgevärsavtryckare. 100% drop-in—inget behov av bönsmide, passning eller justering. Alla komponenter är fångade i det lätta, aluminiumlegerade huset. Hammaren är tråd-EDM bearbetad från S7 verktygsstål som kombinerar hårdhet för att motstå slitage med överlägsen stötmotstånd för att tåla hård användning utan att spricka eller brytas. Andra komponenter är EDM-skurna från A2 verktygsstål, sedan värmebehandlade till Rc 56-60 för lång livslängd. Precisionsslipade engagemangsytor säkerställer suverän tillförlitlighet och en skarp, ren hammareutlösning. Installeras med ditt gevärs ursprungliga hammare/trigger stift; proprietär design eliminerar stiftvandring. AR-.308 modellen har en fabriksinställd 4 lb. avtryckarvikt, en solid sko och mer hammarmassa för att säkerställa positiv tändning av hårdare .308/7.62mm tändhattar.

SPECIFIKATIONER: Hammare – S7 verktygsstål, naturlig färg, Teflon-Nickel belagd. Trigger/Interna komponenter - Härdat A2 verktygsstål, svartoxiderad yta. Hus – 6061 T6 aluminium, guld anodiserad yta. Passar gevär med 0,154" diameter på hammare/trigger stift hål. Passar inte Colt-tillverkade AR-15 med säkerhetsblock. AR-.308 – icke-justerbar 4 lb. avtryckarvikt. Passar AR-stil .308 gevär som accepterar små-stift AR-15 triggerkomponenter.

Mer...

Kundernas betyg påTIMNEY AR .308 TRIGGER MODULE, 4 LBS, SOLID SHOE

Antal betyg: 12
Från brownells.com: 12
Medelbetyg: 4,7

Nothing to Write Home About (2010-07-02)

This trigger is difficult to install. There are two tiny allen head lock screws that must be manuvered into place next to the hammer springs. Very hard to do without three hands.
Performance is only so-so after installation. No take up or slop but it seems to be set at about 8 pounds.
Better than the stock trigger to be sure but not worth the money. Timney usually does a better job on their triggers.

AR-.308 Trigger Module, Solid Shoe (2010-07-19)

Installed mine quite easily. Instructions are adequate but could be improved and Timney has techs available to assist/answer questions. There might be a small amount of creap in mine but if so, I see it as a good thing for this application.

Best thing I have added to my AR Varmint (2011-05-24)

I have built several AR's over the past several years, but always stoned the triggers and added lighter springs to get a better trigger pull. I wanted a 'drop in unit', and having had great results with other "Timmney" Triggers, went with this unit. This trigger is amazing compared to any other trigger I have used in a AR. As for the two screws that had to be installed, I spet maybe a full sixty seconds getting both in and tight. No problem!!

Make em Jealous. (2011-09-15)

I installed this trigger in my SASS build project. Took the rifle to the gon shop because of an unrelated issue. The people at the shop fell in love with the trigger just like I did. In fact one of the gunsmiths had a SASS and the first thing out of his mouth is "man, im jealous of that trigger." Its smooth and exact. Im going to install a Timney in my Remington Woodsmaster if they make one.

Wow, what a difference! (2011-12-30)

I recommend this trigger. The pull is consistent and the break is very clean. If you own a stock DPMS LR-308 with a factory trigger that takes FOREVER to break, you will not be disappointed with this purchase. I installed it myself after I watched a couple of videos as well as going to Timney's website and viewing the installation presentation. On a side note, if you are not mechanically inclined, have a friend install it who is.

GREAT TRIGGER!!! Hard to install (2012-01-11)

I have built many AR's and have done many trigger Jobs for customers and friends, but this trigger is GOLD right out of the box. IT is very difficult to install, not impossible, but not easy by ones self. making sure the trigger pins stay seated as you tighten the two allens can be frustrating but it is well worth it in the end. My trigger feels about 3 pounds at the most.... no creep, exactly what I expect from a [$] trigger.

I want to rate this trigger 10 stars! (2012-06-02)

Unquestionably the best upgrade/modification to my DPMS ar-15! Accuracy much improved from stock trigger. Easy install too. There are two retaining hex screws under the end length of the hammer spring that can be tricky. After studying the trigger & install instructions I took the ends of the hammer spring partially blocking the retainer hex screws & lifted both ends crossing them to the middle over each other. This cleared the area for installing the hex retaining screws. After both hex screws were installed, the hammer spring ends were uncrossed and fell back into their original place. The 4 lbs pull was unchanged by the prying up & crossing of the spring ends. Excellent trigger! Well worth the $$

Excellent! (2014-01-15)

Installed in a Ruger SR762 in minutes, per instructions. Would recommend watching You Tube related video. Went from factory 10.75 lb drag and creep to a crisp 4.0 lb trigger.

Great AR upgrade. (2015-01-02)

Easy install in my Bushmaster. Crisp trigger that took the long, hard, gritty pull out of my AR 10. I will buy another one for my 5.56. Can't wait to see how it performs at the range.

Phoned in. (2015-03-25)

4 lb pull is too heavy, I don't know why Timney made it so heavy. 3lb would have been perfect. They make a good trigger, but I think they have been resting on their laurels.

Nothing Not To Like (2015-06-23)

My first experience with Timney triggers was one I bought for my 10/22. Total drop in, great fit, great trigger. So I got this one for my DPMS style .308 AR build and it is everything I expected. Two triggers purchased, two great feeling triggers; do I detect a pattern?

Iâve purchased stripped AR lowers and built them up. With the last one I purchased a Ni Boron set and that was the best AR trigger Iâd tried. Iâm mentioning this to point out that I *DO* know how to install Mil Spec triggers and know what a good one feels like. Since I wanted a rifle that would be as accurate as possible I decided to actually put some money into this trigger. I could have gone with other manufacturers but while I do know how to install the fire control group I can get a bit lazy from time to time. So I looked into drop in triggers.

I wanted a trigger that was light enough to not impact my accuracy too much (Iâve got enough problems as is) but was heavy enough that I wouldnât worry about safety out in the field. Timneyâs 4 pound trigger seems to fit the bill. I followed the directions and installation was a snap. I saw one review complaining about the pins falling out. I had to laugh as the directions said to put a piece of tape over the pins until installation was complete. Once youâve tightened down the set screws to apply pressure to the pins (the last step) you can remove the tape and the pins are as tight as you could possibly want.

Iâve tried custom worked triggers on other guns at the range (not my guns but ones belonging to someone else) and while they might be a bit lighter I donât think that they break any crisper or have any less creep (i.e. none).

Any time I want an accurate trigger that is easy to install Iâm going to go with Timney for sure.

Crisp - Zero Creep in a DPMS GII Lower (2016-01-11)

No more creep. Light, repeatable release and feels like winding a Swiss watch while depressing the trigger. Trigger total movement is about 1/8"!

Instructions were spot on. Read them through first. One change would be to start the set screws before you drop it in. Just a turn. Too much and the pins won't go back in. After you have the assembly in position it's a bit of a chore to get them started because of the springs. Use grease in the socket to hold the screws to the wrench.

I put this in a new DPMS Gen II lower. Fits like a glove. The GII lower is different than the GI (LR-308) but rest assured it fits perfectly.

The hammer is bigger than the GII OEM hammer. The whole thing is a piece of art. High quality metal and finish.

Worth the money.

Läs 12 fler betyg på brownells.com

5499 5499 1 SEK

Produktnr: 883000023
TIMNEY AR .308 TRIGGER MODULE, 4 LBS, SOLID SHOE
Tillverkarens produktnummer: 670 081950006700 Självständig modul är redo att installeras i din small-pin AR och leverera en exceptionellt mjuk, skarp, krypfri enstegs avtryckarupplevelse som känns mer som en traditionell repetergevär än en stridsgevärsavtryckare. 100% drop-in—inget behov av bönsmide, passning eller justering. Alla komponenter är fångade i det lätta, aluminiumlegerade huset. Hammaren är tråd-EDM bearbetad från S7 verktygsstål som kombinerar hårdhet för att motstå slitage med överlägsen stötmotstånd för att tåla hård användning utan att spricka eller brytas. Andra komponenter är EDM-skurna från A2 verktygsstål, sedan värmebehandlade till Rc 56-60 för lång livslängd. Precisionsslipade engagemangsytor säkerställer suverän tillförlitlighet och en skarp, ren hammareutlösning. Installeras med ditt gevärs ursprungliga hammare/trigger stift; proprietär design eliminerar stiftvandring. AR-.308 modellen har en fabriksinställd 4 lb. avtryckarvikt, en solid sko och mer hammarmassa för att säkerställa positiv tändning av hårdare .308/7.62mm tändhattar.

5499 SEK 7 5 499,00 kr *

Levernastid ca. 14-21 dagar.
7 st. i centrallagret.

Funktioner: Make: AR .308 Stil: Non-Adjustable

Lägg till i inköpslista

Fråga om produkt

Information

Lägg till i inköpslista

Fråga om produkt

Top takeaways

Timney AR .308 Trigger Module är en drop-in modul som ger en mjuk, skarp och krypfri avtryckarupplevelse utan behov av justeringar.
Komponenterna är tillverkade av högkvalitativt verktygsstål och aluminiumlegering för hållbarhet och pålitlighet.
Den har en fabriksinställd 4 lb. avtryckarvikt och är kompatibel med AR-stil .308 gevär som accepterar små-stift AR-15 triggerkomponenter.

Produktinformation

Make: AR .308 Stil: Non-Adjustable Leveransvikt: 0,068kg Leveranshöjd: 33mm Leveransbredd: 91mm Leveranslängd: 191mm

Produkt detaljer

Tillverkas i USA
USA: s exportklassificering: 0A501.c

Uppgradera din AR .308 med TIMNEY's drop-in trigger modul! 🍂 Med en 4 lb avtryckarvikt och solid sko, får du en skarp och krypfri avtryckarupplevelse. 🚀 Lär dig mer!

Obtain A Super-Smooth Pull & Crisp Letoff In Minutes

Mer...

Få Ett Supermjukt Avtryck & Skarpt Avsläpp På Minuter

Mer...

Kundernas betyg påTIMNEY AR .308 TRIGGER MODULE, 4 LBS, SOLID SHOE

Antal betyg: 12
Från brownells.com: 12
Medelbetyg: 4,7

Nothing to Write Home About (2010-07-02)

AR-.308 Trigger Module, Solid Shoe (2010-07-19)

Best thing I have added to my AR Varmint (2011-05-24)

Make em Jealous. (2011-09-15)

Wow, what a difference! (2011-12-30)

GREAT TRIGGER!!! Hard to install (2012-01-11)

I want to rate this trigger 10 stars! (2012-06-02)

Excellent! (2014-01-15)

Installed in a Ruger SR762 in minutes, per instructions. Would recommend watching You Tube related video. Went from factory 10.75 lb drag and creep to a crisp 4.0 lb trigger.

Great AR upgrade. (2015-01-02)

Easy install in my Bushmaster. Crisp trigger that took the long, hard, gritty pull out of my AR 10. I will buy another one for my 5.56. Can't wait to see how it performs at the range.

Phoned in. (2015-03-25)

4 lb pull is too heavy, I don't know why Timney made it so heavy. 3lb would have been perfect. They make a good trigger, but I think they have been resting on their laurels.

Nothing Not To Like (2015-06-23)

Crisp - Zero Creep in a DPMS GII Lower (2016-01-11)

Läs 12 fler betyg på brownells.com

Kunder har även köpt

CLYMER 22 LONG RIFLE HEADSPACE GAUGE KIT
GO/NO-GO GAUGE SETS

CLYMER

Lagervara

1 349,00 kr * 1 249,00 kr - 1 849,00 kr*

Headspace Gauges

4,9

L.E. WILSON 257 WEATHERBY MAGNUM FIRED CASE HOLDER
RIFLE CASE HOLDERS

L.E. WILSON

Lagervara

259,00 kr * 219,00 kr - 359,00 kr*

Svarv Hylshållare | Hylssvarvar

3,8

HORNADY RAPID RACK AR-15
RAPID RACK

HORNADY

Slut i lager

319,00 kr *

Chamber Säkerhetsflagga

JAMES MADISON TACTICAL AR-15 SABER DROP IN SINGLE STAGE TRIGGER
AR-15 SABER DROP IN SINGLE STAGE TRIGGER

JAMES MADISON TACTICAL

Lagervara

1 999,00 kr *

Avtryckare

3,8

Logga in

Har du glömt lösenordet?
Registrering

Varför beställa från oss?

Oöverträffat produktutbud

Det du vill ha? Vi har det!

Expertkundrådgivning

Via telefon, chatt och e-post

USA-varor till din dörr

Inga tullar, inga problem

100 dagars returer

Handla med sinnesfrid

Erbjudanden, kampanjer och exklusiva produkter

Genom vårt nyhetsbrev

Ärlighet

Vi uppmuntrar kritisk produktrecension

Rättvis prissättning

Vi driver en hållbar prispolitik

Vi lämnar dig inte strandsatt

Hela vårt team består av passionerade vapenentusiaster

HEMSIDA

PRODUKTKATEGORI

BESTÄLLNING

KUNDSERVICE

Anslut

Säkra betalningsmetoder

Branschorganisationer

cf-web-badges-e-ltgray

Välkommen till oss!

till Brownells Sverige, din destination för allt vapenrelaterat. Med våra rötter i en genuin passion för skjutvapen, ger vi dig ett oöverträffat urval av vapendelar, skjutvapen tillbehör, vapensmedsverktyg, kikarsikten & rödpunktsikten och expertkunskap.

Oavsett om du vill underhålla, reparera eller uppgradera så har vi det du behöver!

För skyttar, av skyttar
Vi delar din entusiasm och vet exakt vad du letar efter eftersom vi är en del av gemenskapen.

Massivt urval
Från det väsentliga till det unika, hitta allt under ett tak.

Vår blandning av tradition och innovation
Handla med bekvämligheten av modern teknik, uppbackad av ett arv av erfarenhet.

Bläddra i vår samling och upptäck varför vi är det pålitliga namnet inom skyttesport och jakt.