Brownells Sverige - Komplett utbud av laddutrustningar, vapendelar, skyttetillbehör, kulor, hylsor och optik Sverige

EGW
S&W K, L, N, X FRAME REVOLVERS VORTEX RAZOR SIGHT MOUNT

841370113019 296000691
Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: Smith & Wesson K Frame Revolvers Smith & Wesson L Frame Revolvers Smith & Wesson N Frame Revolvers Smith & Wesson X Frame Revolvers If your revolver is not drilled and tapped this mount will not work. The best way to verify that it is/is not drilled and tapped is to open the cylinder and check the rib underneath. There should be through holes that are drilled and tapped. If there are not (like the above image) this mount will not work without you having the gun drilled and tapped. You can have a competent and qualified gunsmith drill and tap the top strap with the standard S&W hole pattern which will allow you to use our mount.  
899 899 1 SEK
Produktnr: 296000691
EGW SIGHT MOUNT FOR VORTEX RAZOR FITS S&W K, L, N, X FRAME BLACK
Tillverkarens produktnummer: 49438 841370113019 Ta enkelt bort bakre siktet på ditt vapen och ersätt det med EGW-fästet för att montera ditt Vortex Razor, C-More RTS eller STS rödpunktsikte. Du kan när som helst ta bort fästet och återmontera ditt bakre sikte. Monteringstillbehör ingår. Installationsinstruktioner: Ta bort bakre sikte* Installera EGW Sight Mount i svansen Dra åt ställskruven (om tillämplig) Placera rödpunktsiktet på EGW Sight Mount (att placera en liten bit papper mellan rödpunktsiktet och siktesfästet kommer att underlätta borttagningen och hålla Loctite borta från rödpunktsiktet.) Applicera blå Loctite på de medföljande monteringsskruvarna Dra åt monteringsskruvarna till 15in/lbs De skruvar som medföljer detta fäste kräver en 5/64'' insexnyckel för installation. Detta fäste passar: Smith & Wesson K Frame Revolvers Smith & Wesson L Frame Revolvers Smith & Wesson N Frame Revolvers Smith & Wesson X Frame Revolvers Om din revolver inte är borrad och gängad kommer detta fäste inte att passa. Det bästa sättet att verifiera om den är/inte är borrad och gängad är att öppna cylindern och kontrollera ribban undertill. Det bör finnas genomgående hål som är borrade och gängade. Om det inte finns några (som på bilden ovan) kommer detta fäste inte att fungera utan att du får vapnet borrat och gängat. Du kan anlita en kompetent och kvalificerad vapensmed för att borra och gänga toppremmen med det standardmässiga S&W hålmönstret vilket kommer att tillåta dig att använda vårt fäste.
899 SEK 1 899,00 kr *
Levernastid ca. 14-21 dagar.
1 st. i centrallagret.
Funktioner: Basantal: 1-Piece Färg: Svart Make: Smith & Wesson Material: Aluminum Modell: K Frame, L Frame, N Frame, X Frame Stil: Tactical

Produktinformation

Antal Baser: 1-Piece Färg: Svart Make: Smith & Wesson Material: Aluminum Modell: N Frame,K Frame,X Frame,L Frame Stil: Tactical Leveransvikt: 0,045kg Leveranshöjd: 25mm Leveransbredd: 76mm Leveranslängd: 140mm

Produkt detaljer

Tillverkas i USA



Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: Smith & Wesson K Frame Revolvers Smith & Wesson L Frame Revolvers Smith & Wesson N Frame Revolvers Smith & Wesson X Frame Revolvers If your revolver is not drilled and tapped this mount will not work. The best way to verify that it is/is not drilled and tapped is to open the cylinder and check the rib underneath. There should be through holes that are drilled and tapped. If there are not (like the above image) this mount will not work without you having the gun drilled and tapped. You can have a competent and qualified gunsmith drill and tap the top strap with the standard S&W hole pattern which will allow you to use our mount.  
Nyhetsbrev