Brownells Sverige - Komplett utbud av laddutrustningar, vapendelar, skyttetillbehör, kulor, hylsor och optik Sverige
697566711152 430103596
BIS, G43X/48 (Backup Iron Sight, G43X/G48) is a collaboration between Ameriglo and FCD. Specifically made for Glock G43X and G48, these sights are based on the superb Ameriglo GL-527 with a front sight height of 0.450", and a rear sight height of 0.554", this sight sets provide lower 1/3 co-witness with the Trijicon RMRcc when used with the OPF-G43X/43, RMRcc on G43X and G48. BIS, G43X/48 consists of the following: Front sight, available with either green Tritium and white outline (no serrations), or serrated front sight, no tritium or white outline. Rear sight, serrated. BIS, G43X/48 is slightly different from GL-527 on which it's based. These FCD particular changes are: Tritium option for the front sight. Front sight back strap angle is steeper (25 degrees on the serrated, non-tritium front sight, 20 degrees on non-serrated, tritium front sight) to mitigate snagging when the pistol is drawn from and out of the holster where it's likely to encounter clothing, and the front sight's top corners are softened. Rear sight is horizontally serrated. Designed and made in the USA. Special thanks to the professionals at Ameriglo https://ameriglo.com/ that made this project possible, Forward Controls Design are grateful for their willingness to work with a small outfit for their shared customers / users. G43X/49 with RMRcc is approved by many agencies, most of which require red dot pistols be equipped with metallic, co-witnessing backup sights for both on and off duty use. BIS, G43X/48 was created with them in mind. NOTE: If you don't have a sight pusher or the equipment to install rear sights, please bring it to a qualified and competent gunsmith to perform the installation. It's not uncommon to have to fit the rear sight to the dovetail, a competent gunsmith should be well familiar with the reason and method. Forward Controls Design have seen more than enough expensive muzzle devices ruined by "gunsmiths" that used a screw driver to install them instead of a torque wrench, and hand tightened optics plate screws when a torque value is clearly noted in multiple places. Rather than being loose (easy to install), Forward Controls Design prefer the sights be tight, so it won't be knocked off zero easily. Tolerances of the dovetail and sights also come into play, which results in some being easier, while others are harder to install. A qualified gunsmith can deal with these easily.  
1649 1649 1 SEK
Produktnr: 430103596
FORWARD CONTROLS DESIGN GLOCK G43X/G48 BACKUP IRON SIGHT WITH TRITIUM
Tillverkarens produktnummer: BIS, 43X/48, WI 697566711152 BIS, G43X/48 (Backup Iron Sight, G43X/G48) är ett samarbete mellan Ameriglo och FCD. Speciellt framtagen för Glock G43X och G48, baseras dessa sikten på det utmärkta Ameriglo GL-527 med en kornhöjd på 0.450\", och ett bakre sikte på 0.554\", detta sikteset ger lower 1/3 co-witness med Trijicon RMRcc när det används med OPF-G43X/43, RMRcc på G43X och G48. BIS, G43X/48 består av följande: Korn, tillgängligt antingen med grönt Tritium och vit kontur (inga räfflor), eller räfflat korn, inget tritium eller vit kontur. Bakre sikte, räfflat. BIS, G43X/48 skiljer sig något från GL-527 som det är baserat på. Dessa specifika FCD-ändringar inkluderar: Tritiumalternativ för kornet. Kornets baksidesvinkel är brantare (25 grader på det räfflade, icke-tritium kornet, 20 grader på det icke-räfflade, tritium kornet) för att minska risken för fasthakning när pistolen dras från och tillbaka i hölstret där den sannolikt kommer i kontakt med kläder, och kornets övre hörn är mjukgjorda. Bakre sikte är horisontellt räfflat. Designad och tillverkad i USA. Ett speciellt tack till proffsen på Ameriglo https://ameriglo.com/ som gjorde detta projekt möjligt, Forward Controls Design är tacksamma för deras vilja att arbeta med ett mindre företag för deras gemensamma kunder/användare. G43X/49 med RMRcc är godkänd av många myndigheter, de flesta av dem kräver att pistoler med rödpunktsikte är utrustade med metalliska, co-witnessing backup sikten för både tjänst och privat bruk. BIS, G43X/48 skapades med dem i åtanke. NOTERA: Om du inte har en siktflyttare eller utrustningen för att installera bakre sikten, vänligen ta med den till en kvalificerad och kompetent vapensmed för installation. Det är inte ovanligt att behöva passa in det bakre siktet i skåran, en kompetent vapensmed bör vara väl bekant med anledningen och metoden. Forward Controls Design har sett alltför många dyra mynningsanordningar förstörda av \"vapensmeder\" som använt en skruvmejsel för att installera dem istället för en momentnyckel, och handåtdragna optikplatteskruvar när ett momentvärde tydligt anges på flera ställen. Hellre än att vara lösa (lätt att installera), föredrar Forward Controls Design att siktet är tajt, så att det inte enkelt kan komma ur sitt nolläge. Toleranser för skåran och siktena spelar också in, vilket resulterar i att vissa är lättare, medan andra är svårare att installera. En kvalificerad vapensmed kan enkelt hantera dessa.
1649 SEK 4 1 649,00 kr *
Leveranstid ca. 14-21 dagar.
4 st. i centrallagret.
Funktioner: Make: Glock Modell: 48, 43X Siktesfärg: Grön Stil: Tritium

Produktinformation

Make: Glock Modell: 43X,48 Siktesfärg: Grön Stil: Tritium Leveransvikt: 0,363kg Leveranshöjd: 5mm Leveransbredd: 152mm Leveranslängd: 102mm

Produkt detaljer

Tillverkas i USA



BIS, G43X/48 (Backup Iron Sight, G43X/G48) is a collaboration between Ameriglo and FCD. Specifically made for Glock G43X and G48, these sights are based on the superb Ameriglo GL-527 with a front sight height of 0.450", and a rear sight height of 0.554", this sight sets provide lower 1/3 co-witness with the Trijicon RMRcc when used with the OPF-G43X/43, RMRcc on G43X and G48. BIS, G43X/48 consists of the following: Front sight, available with either green Tritium and white outline (no serrations), or serrated front sight, no tritium or white outline. Rear sight, serrated. BIS, G43X/48 is slightly different from GL-527 on which it's based. These FCD particular changes are: Tritium option for the front sight. Front sight back strap angle is steeper (25 degrees on the serrated, non-tritium front sight, 20 degrees on non-serrated, tritium front sight) to mitigate snagging when the pistol is drawn from and out of the holster where it's likely to encounter clothing, and the front sight's top corners are softened. Rear sight is horizontally serrated. Designed and made in the USA. Special thanks to the professionals at Ameriglo https://ameriglo.com/ that made this project possible, Forward Controls Design are grateful for their willingness to work with a small outfit for their shared customers / users. G43X/49 with RMRcc is approved by many agencies, most of which require red dot pistols be equipped with metallic, co-witnessing backup sights for both on and off duty use. BIS, G43X/48 was created with them in mind. NOTE: If you don't have a sight pusher or the equipment to install rear sights, please bring it to a qualified and competent gunsmith to perform the installation. It's not uncommon to have to fit the rear sight to the dovetail, a competent gunsmith should be well familiar with the reason and method. Forward Controls Design have seen more than enough expensive muzzle devices ruined by "gunsmiths" that used a screw driver to install them instead of a torque wrench, and hand tightened optics plate screws when a torque value is clearly noted in multiple places. Rather than being loose (easy to install), Forward Controls Design prefer the sights be tight, so it won't be knocked off zero easily. Tolerances of the dovetail and sights also come into play, which results in some being easier, while others are harder to install. A qualified gunsmith can deal with these easily.  
Nyhetsbrev