Brownells Sverige - Komplett utbud av laddutrustningar, vapendelar, skyttetillbehör, kulor, hylsor och optik Sverige
841370113958 296000698
Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended* The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount does not fit: Smith & Wesson M&P C.O.R.E Series (Already optics ready) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering. Our return policy does allow for returns of unused and undamaged parts. These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.  
899 899 1 SEK
Produktnr: 296000698
EGW SIGHT MOUNT FOR VORTEX RAZOR FITS S&W M&P BLACK
Tillverkarens produktnummer: 49445 841370113958 Ta enkelt bort bakre sikten på ditt vapen och ersätt den med EGW monteringen för att kunna montera ditt Vortex Razor, C-More RTS eller STS rödpunktsikte. Du kan när som helst ta bort monteringen och sätta tillbaka ditt bakre sikte. Monteringshårdvara ingår. Installationsinstruktioner Ta bort bakre sikten* Installera EGW Siktesmonteringen i svansen Strama åt ställskruven (om tillämplig) Placera rödpunktsiktet på EGW Siktesmonteringen (att placera en liten bit papper mellan rödpunktsiktet och siktesmonteringen kommer att underlätta borttagning och hålla Loctite borta från rödpunktsiktet.) Applicera blå Loctite på de medföljande monteringsskruvarna Dra åt monteringsskruvarna till 15in/lbs *Verktyg för att trycka ut bakre sikten rekommenderas starkt* Skruvarna som medföljer denna montering kräver en 5/64'' insexnyckel för installation. Denna montering passar inte: Smith & Wesson M&P C.O.R.E Series (Redan optikförberedd) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE Smith and Wessons bakre siktesvansar är kända för att variera i dimensioner. Våra sikten är gjorda med samma toleranser. Vissa användare kan ha problem med att installera vår platta på deras släde på grund av de varierande toleranserna i era slädar. Vänligen ha detta i åtanke när ni beställer. Vår returpolicy tillåter returer av oanvända och oskadade delar. Dessa monteringar bör installeras och kontrolleras av en kvalificerad vapensmed. Inget ansvar uttrycks eller antyds för skada eller skada som kan uppstå på grund av felaktig installation eller användning av denna produkt.
899 SEK 0 899,00 kr *
Restorder. Skickas när den finns i lager. Leveranstid ca 4-12 veckor från centrallagret.
Funktioner: Basantal: 1-Piece Färg: Svart Make: Smith & Wesson Material: Aluminum Modell: M&P Shield, SD40, M&P 2.0 Compact, SD9-VE, M&P 22 FS, M&P FS Stil: Tactical

Produktinformation

Antal Baser: 1-Piece Färg: Svart Make: Smith & Wesson Material: Aluminum Modell: M&P 2.0 Compact,M&P FS,SD40,SD9-VE,M&P 22 FS,M&P Shield Stil: Tactical Leveransvikt: 0,045kg Leveranshöjd: 25mm Leveransbredd: 76mm Leveranslängd: 140mm

Produkt detaljer

Tillverkas i USA



Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended* The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount does not fit: Smith & Wesson M&P C.O.R.E Series (Already optics ready) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering. Our return policy does allow for returns of unused and undamaged parts. These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.  
Nyhetsbrev