Hiperfire’s EDT triggers give your AR-15 an upgraded single-stage trigger pull without sacrificing "mil-spec" reliability. All four Enhanced Duty Triggers deliver a medium pull weight of 4.5 or 5.5 lbs. - lighter than a plain G.I. trigger for sure, but safe enough for law enforcement, service rifle competition, and personal defense use. Mechanical advantage built into the EDT trigger geometry gives the lighter-than-mil-spec pull weight, while mil-spec hammer energy is preserved to ensure hard, positive primer strikes. Hiperfire coupled the lighter weight with an overall pull profile that is smooth and consistent, with a clean, decisive break, short over-travel, and a fast reset you can feel and hear, making the EDT a very comfortable "shooter’s" trigger. Single-stage with minimal creep 2 interchangeable hammer springs for 4.5 or 5.5 lb. pull weight SwingFast Hammer Head™ gives unusually fast locktime Extra-power hammer spring for positive hammer strikes without increasing pull weight Self-cleaning - designed to allow debris to fall out to prevent jams & reset problems Fits small-pin (.153") AR-15 lower receivers & AR 308 rifles that use AR-15 triggers Hiperfire offers the EDT trigger in four configurations: Sharp Shooter is the base-model with features listed above and a curved trigger shoe. Heavy Gunner has the curved shoe and even heavier SwingFast hammer than the Sharp Shooter for ultra-reliable hammer strikes. The Designated Marksman has Hiperfire's Duplex Trigger Bow. Place your finger in a high position for a heavier pull and an extra measure of safety to prevent premature discharge under stress. Low position for precise, target-rifle control. Also has extra-weight Swingfast hammer. Enhanced Duty model is beefed up for full-auto select-fire AR-15 / M16 / M4 type rifles carbines; curved shoe. Hiperfire made the EDT trigger line all about choice: you get to choose the type of trigger pull profile that works best for you - without breaking the bank to do it.
Uppgradera din AR-15 med Hiperfire EDT® avtryckarsystem
Hiperfires EDT-avtryckare ger din AR-15 en uppgraderad enstegs avtryckarpull utan att kompromissa med "mil-spec" pålitlighet. Alla fyra Enhanced Duty Triggers levererar en medelviktsdragning på 4,5 eller 5,5 lbs - lättare än en vanlig G.I. avtryckare, men tillräckligt säker för brottsbekämpning, tävling med tjänstegevär och personlig försvarsanvändning.
Funktioner:
- Enstegs med minimal creep
- 2 utbytbara hammarfjädrar för 4,5 eller 5,5 lbs dragvikt
- SwingFast Hammer Head™ ger ovanligt snabb låsningstid
- Extra kraftig hammarfjäder för positiva hammarslag utan att öka dragvikten
- Självrengörande - designad för att låta skräp falla ut för att förhindra fastkörningar och återställningsproblem
- Passar små-pinniga (.153") AR-15 underreceivrar och AR 308 gevär som använder AR-15 avtryckare
Hiperfire erbjuder EDT-avtryckaren i fyra konfigurationer:
- Sharp Shooter: basmodellen med ovanstående funktioner och en böjd avtryckarsko.
- Heavy Gunner: har den böjda skon och en ännu tyngre SwingFast-hammare än Sharp Shooter för ultra-pålitliga hammarslag.
- Designated Marksman: har Hiperfires Duplex Trigger Bow. Placera fingret i en hög position för en tyngre dragning och ett extra mått av säkerhet för att förhindra för tidig avfyrning under stress. Låg position för precis kontroll som på ett målgevär. Har också extra tung Swingfast-hammare.
- Enhanced Duty: förstärkt för fullautonom selektiv avfyrning av AR-15 / M16 / M4-typ gevär; böjd sko.
Hiperfire har gjort EDT-avtryckarlinjen helt inriktad på val: du får välja den typ av avtryckarpullprofil som fungerar bäst för dig - utan att spräcka banken för att göra det.