Produktinformation
- Vapentyp: AR-15
- Leveransvikt: 0,181kg
- Leveranshöjd: 5mm
- Leveransbredd: 66mm
- Leveranslängd: 229mm
- UPC: 050806107236
Produktnr: 080000291
050806107236 Vårt praktiska, kompakta verktyg är unikt utformat för att kombinera flera verktyg i ett. Det har en skiftnyckel som passar mottagarens förlängningens castle nut på M4-stilens ihopvikbara buttstocks, med utbytbara stift för att passa muttrar med både gammal (rund) och ny (fyrkantig) tandning, så att du är redo för vilken typ av mutter som helst på vapnet framför dig. Stift för båda stilar ingår och kan enkelt bytas genom att lossa en sexkantsskruv i verktyget. För fasta gevärsbuttstocks finns det en skruvmejselblad för att ta bort buttplattans skruvar och en nyckel för muttern på mottagarens förlängning (buffer) rör. Det finns till och med en ½" fyrkantig öppning för en momentnyckel, och en hål för att hänga verktyget på din peg-board. Passar lätt i en skjutväska eller i fickan för användning utanför verkstaden.
Fri frakt från 2 999 kr.
Levernastid ca. 14-21 dagar.
Vårt praktiska verktyg är unikt utformat för att kombinera flera verktyg i ett. Det har en spanner wrench som passar mottagarens förlängnings castle nut på M4-stilens hopfällbara buttstocks, med utbytbara pinnar för att passa muttrar med både gamla (runda) och nya (fyrkantiga) tänder, så att du är redo för vilken typ av mutter som helst på vapnet framför dig.
Verktyget passar lätt i en range bag eller i fickan för användning utanför verkstaden.
Great tool, just one hiccup 2015-11-22
So I gave this 5 stars, despite my hiccup.
This tool is great, it's really well made and feels incredibly sturdy.
My hiccup occurred because I used it on a barrel nut, not a buttstock. If you're using this for your buttstock, no need to read any further...
The Centurion CMR handguard does not come with a tool. Centurion says that you should use a buttstock tool to install the barrel nut since it is the same diameter as the castlenut on a carbine stock. The problem is that you have to use a tool that has one "nub" on it, not three like most others have. These "nubs" aren't meant to torque a barrel nut to 30ft/lbs.
I used my generic amazon AR15 tool to install the barrel nut and caused the "nub" to break off. I bought this thinking it may work for me. This tool has a small replaceable pin (as pictured), which bent and became unusable almost instantly. Luckily, I was able to use a 1/8in punch in the hole perfectly fine.
I'm still 100% happy with this tool, the pin broke because it wasn't designed for the torque but luckily it has a great design where you can replace the pin.
Obviously, the only thing I would change about this is tool is for it to come with a stronger pin. However, if you're building an AR15 you should already have an assortment of punches, which you can use with this tool.
Well made. Inspired confidence. 2014-04-01
I purchased this tool with some concern. I have an older AR-15 that had a 2 position collapsible stock with the 2 round holes instead of the normal castle nut and were well staked in place. I had been told how difficult some staked castle nuts were to remove. A friend who has built several AR-15's suggested just cutting the castle nut with a dremel which would likely destroy the tube as well. I wanted to remove the parts but retain them for collectors purposes and switch them out for a current 6 position stock tube. I just clamped the lower receiver in a vise using Brownells rubber faced vise jaws and was able to remove the ring without damage to the lower or the castle nut. I did tap the wrench with a plastic mallet several times before attempting to loosen the castle nut. This tool worked like a charm and I have already told several other people how well it worked. Brownells guarantee gave me the confidence to try it myself instead of paying someone else to remove the stock nut for me.
Vi stötte på ett fel när vi laddade innehållet. Vänligen uppdatera sidan för att fortsätta. Om problemet kvarstår, kontakta vår kundtjänst.