This is one of the most useful maintenance accessories available for an AR-10. Simply bolt or clamp securely to a bench or other work surface, place an AR 308 rifle onto the block inside the magazine well, and the rifle is held in place for cleaning, maintenance, or storage. 1-piece glass filled polymer design Fits rifles that use SR-25 pattern magazines Weight: .7oz 6-1/8" tall x 2" long(at the base) x 4-1/4" wide (at the base) 1/4" mounting holes
Mer...
Detta är ett av de mest användbara underhållstillbehören för en AR-10. Fäst enkelt med bult eller klämma säkert till en bänk eller annan arbetsyta, placera en AR 308-gevär på blocket inne i magasinsbrunnen, och geväret hålls på plats för rengöring, underhåll eller förvaring. 1-delad design i glasfylld polymer Passar gevär som använder SR-25 mönstermagasin Vikt: 19,8g 15,6 cm hög x 5 cm lång (vid basen) x 10,8 cm bred (vid basen) 6,35 mm monteringshål
Mer...
Kundernas betyg påERGO GRIPS 308 AR ARMORERS BLOCK
Antal betyg: 3
Från brownells.com: 3
Medelbetyg: 3
Much stronger than pivoting types(2015-12-27)
After breaking two of the pivoting types of these I purchased this. I have had no problems removing and installing muzzle devices, removing or tightening castle nuts on receiver extensions, or performing any other types of work using this. I simply screwed it to my work bench. I works with the lower receiver right side up or upside down which makes installing grip screws easier.
If your rifle uses MagPul P-MAgs then this block will be real sloppy and a block of wood wrapped with Gorilla tape would be better.
The block measures: 2.93 X 1.029. If you add 2 wraps of Duct Tape it will work: but if it were made properly, that would not be necessary. Block needs to be at least: 3.00X 1.00; and preferably 3.07X1,06 for a snug fit.
Needless to say I'm returning the block.
if the dimensions on the BROWNELLS - 308 AR LOWER RECEIVER VISE BLOCK 080-000-494WB are correct, it should fit perfectly for MagPul .308 P-Mag users.
Machinist, Gunsmith, Mechanic, Shooter for over 65 years, disabled Navy Vet..
Block sits loose and sloppy in my XCR-M, barely clicks into the mag release latch.
When upper is unpinned, the lower receiver falls down passed the mag release latch and the block jams up inside the magwell.
I'm considering taking a magazine and welding it to a piece of steel, which makes this block a paper weight. Would have sent it back if it weren't only $20 USD
Produktnr: 573000088 ERGO GRIPS 308 AR ARMORERS BLOCK Tillverkarens produktnummer: 4989874748005548 Detta är ett av de mest användbara underhållstillbehören för en AR-10. Fäst enkelt med bult eller klämma säkert till en bänk eller annan arbetsyta, placera en AR 308-gevär på blocket inne i magasinsbrunnen, och geväret hålls på plats för rengöring, underhåll eller förvaring. 1-delad design i glasfylld polymer Passar gevär som använder SR-25 mönstermagasin Vikt: 19,8g 15,6 cm hög x 5 cm lång (vid basen) x 10,8 cm bred (vid basen) 6,35 mm monteringshål
This is one of the most useful maintenance accessories available for an AR-10. Simply bolt or clamp securely to a bench or other work surface, place an AR 308 rifle onto the block inside the magazine well, and the rifle is held in place for cleaning, maintenance, or storage. 1-piece glass filled polymer design Fits rifles that use SR-25 pattern magazines Weight: .7oz 6-1/8" tall x 2" long(at the base) x 4-1/4" wide (at the base) 1/4" mounting holes
Mer...
Detta är ett av de mest användbara underhållstillbehören för en AR-10. Fäst enkelt med bult eller klämma säkert till en bänk eller annan arbetsyta, placera en AR 308-gevär på blocket inne i magasinsbrunnen, och geväret hålls på plats för rengöring, underhåll eller förvaring. 1-delad design i glasfylld polymer Passar gevär som använder SR-25 mönstermagasin Vikt: 19,8g 15,6 cm hög x 5 cm lång (vid basen) x 10,8 cm bred (vid basen) 6,35 mm monteringshål
Mer...
Kundernas betyg påERGO GRIPS 308 AR ARMORERS BLOCK
Antal betyg: 3
Från brownells.com: 3
Medelbetyg: 3
Much stronger than pivoting types(2015-12-27)
After breaking two of the pivoting types of these I purchased this. I have had no problems removing and installing muzzle devices, removing or tightening castle nuts on receiver extensions, or performing any other types of work using this. I simply screwed it to my work bench. I works with the lower receiver right side up or upside down which makes installing grip screws easier.
If your rifle uses MagPul P-MAgs then this block will be real sloppy and a block of wood wrapped with Gorilla tape would be better.
The block measures: 2.93 X 1.029. If you add 2 wraps of Duct Tape it will work: but if it were made properly, that would not be necessary. Block needs to be at least: 3.00X 1.00; and preferably 3.07X1,06 for a snug fit.
Needless to say I'm returning the block.
if the dimensions on the BROWNELLS - 308 AR LOWER RECEIVER VISE BLOCK 080-000-494WB are correct, it should fit perfectly for MagPul .308 P-Mag users.
Machinist, Gunsmith, Mechanic, Shooter for over 65 years, disabled Navy Vet..
Block sits loose and sloppy in my XCR-M, barely clicks into the mag release latch.
When upper is unpinned, the lower receiver falls down passed the mag release latch and the block jams up inside the magwell.
I'm considering taking a magazine and welding it to a piece of steel, which makes this block a paper weight. Would have sent it back if it weren't only $20 USD