Brownells Sverige - Komplett utbud av laddutrustningar, vapendelar, skyttetillbehör, kulor, hylsor och optik Sverige
080000409
Quickly Remove Firing Pins From Remington & Ruger~ Rifles
A third hand for removing the firing pin from Remington and Ruger® bolt action rifles without lost parts or sore fingers that sometimes accompany this tricky job. Install the correct bushing for your rifle in the end of the tool body. Screw the firing pin assembly into the bushing, and tighten the threaded, steel shank to compress and capture the mainspring. The hollow shank protects the firing pin tip as it slides over the pin to compress the spring. The crosspin can then be driven out with a punch, and the spring tension relieved by gradually loosening the shank. Includes bushings for Remington 700 family and Ruger M77® Mark II rifles. Built-in storage slot holds the unused bushing on the tool body, so it’s always there when you need it. NOTE: Will not fit Ruger Left hand actions.

SPECS: Aluminum base, hardcoat anodized, black. Hardened tool steel screw shank and bushings, black oxide finish. Body - 5¼” (13.34cm) long, 1” (2.54cm) wide, 1-3⁄16" (3.02cm) high. Shank – 3½” (8.89cm) long. Fits Remington 700, 710, 721, 722, Model Seven, XP-100, M24, and 40X; Ruger M77 Mark II, 77/22, 77/17, 77/44 bolt action rifles.

1649 1649 1 SEK
Produktnr: 080000409
BROWNELLS FIRING PIN REMOVAL TOOL Ett tredje handverktyg för att ta bort tändstift från Remington och Ruger® repetergevär utan förlorade delar eller ömma fingrar som ibland följer med detta knepiga jobb. Installera den korrekta bussningen för ditt gevär i verktygskroppens ände. Skruva in tändstiftsmonteringen i bussningen och dra åt den gängade stålskruvaxeln för att komprimera och fånga huvudfjädern. Den ihåliga axeln skyddar tändstiftets spets när den glider över stiftet för att komprimera fjädern. Sprinten kan sedan drivs ut med en dorn, och fjäderns spänning lindras genom att gradvis lossa på axeln. Inkluderar bussningar för Remington 700-familjen och Ruger M77® Mark II gevär. Inbyggd förvaringsplats håller den oanvända bussningen på verktygskroppen, så den är alltid där när du behöver den. OBS: Passar inte Ruger vänsterhandsaktioner.
1649 SEK 0 1 649,00 kr *
Produkten kan beställas som restorder.
Funktioner: Make: Ruger, Remington Modell: Universal Gevär

Produktinformation

Make: Remington,Ruger Modell: Universal Gevär Leveransvikt: 0,431kg Leveranshöjd: 58mm Leveransbredd: 112mm Leveranslängd: 183mm

Produkt detaljer

Tillverkas i USA



Quickly Remove Firing Pins From Remington & Ruger~ Rifles
A third hand for removing the firing pin from Remington and Ruger® bolt action rifles without lost parts or sore fingers that sometimes accompany this tricky job. Install the correct bushing for your rifle in the end of the tool body. Screw the firing pin assembly into the bushing, and tighten the threaded, steel shank to compress and capture the mainspring. The hollow shank protects the firing pin tip as it slides over the pin to compress the spring. The crosspin can then be driven out with a punch, and the spring tension relieved by gradually loosening the shank. Includes bushings for Remington 700 family and Ruger M77® Mark II rifles. Built-in storage slot holds the unused bushing on the tool body, so it’s always there when you need it. NOTE: Will not fit Ruger Left hand actions.

SPECS: Aluminum base, hardcoat anodized, black. Hardened tool steel screw shank and bushings, black oxide finish. Body - 5¼” (13.34cm) long, 1” (2.54cm) wide, 1-3⁄16" (3.02cm) high. Shank – 3½” (8.89cm) long. Fits Remington 700, 710, 721, 722, Model Seven, XP-100, M24, and 40X; Ruger M77 Mark II, 77/22, 77/17, 77/44 bolt action rifles.

Nyhetsbrev