Saves Your "Tail Feathers" If A Hole Gets Stripped
Slightly larger in diameter than the common 6-48 scope base mounting screw. Most holes "ruined" while drilling or tapping can be fixed; just retap to .146"-48 and install. No need to redrill base or gun. Thanks to Doug Knowt for his tip. Click Here for taps.
SPECS: .146"-48x½" (12.7mm) slotted machine screws, blued finish. Fillister and Weaver-style head. Kit contains 48 of each style, 1 taper tap, 1 bottom tap, and 1 Screw Gizzie in a bench box.
Mer...
Räddar dina "svansfjädrar" om ett hål blir stripat
Något större i diameter än den vanliga 6-48 skruven för montering av kikarsiktesbas. De flesta hål som "förstörts" under borrning eller gängning kan lagas; bara gänga om till .146"-48 och installera. Inget behov av att borra om basen eller vapnet. Tack till Doug Knowt för hans tips. Klicka Här för gängtappar.
SPECS: .146"-48x½" (12.7mm) skårad maskinskruv, blånerad finish. Fillister- och Weaver-stil huvud. Kittet innehåller 48 av varje stil, 1 förskärningstapp, 1 botten tapp, och 1 Screw Gizzie i en bänklåda.
Antal betyg: 7
Från brownells.com: 7
Medelbetyg: 4,9
Saves a job gone bad!(2010-09-05)
8-40 Torx screws into a Remington 1100 stripped out the receiver. These screws, combined with the .146"-48 tap worked perfectly! As noted in tips description by Mr. Doug Knowt, no need to re-drill. Just run the tap through, install the oversize screws, and your done! The screw heads were exact size as Torx, and the screws were plenty long enough to grind to fit any application. Thanks Brownell's! Thanks Mr. Knowt!
Just the ticket!(2016-07-01)
I used these in conjunction with the required tap to fix the scope base screw holes in a Remington 597 receiver. The screw holes were a bit oversized as it came from the factory with only .002" of thread engagement.
Excellent fix! - almost perfect(2018-06-14)
I used these in conjunction with the associated tapered tap to fix the scope base screw holes in a Remington 700 receiver. The front two screws from the factory were stripped and would just spin. I had to drive them down through the holes after removing the barrel. The tapered tap did its' job by hand. Used the tap and a 1/8" drill bit on a piece of O-1 steel to allow me to cut and file the screws down to size. The only issue with these screws is the slotted head. My Burris XTR steel scope base calls for 35 in lbs of torque and the little slotted screw head wouldn't hold the bit all of the way to 35 in lbs of torque. A socket head or torx head would do the trick and would have made this solution perfect. Very happy overall though, I recommend this solution for stripped receiver scope base holes.
Receiver saver!(2011-04-14)
This kit was great and easy to use. A friend and I purchased after both had stripped out screws on Ruger 10/22 receivers. Bought this kit and the proper drill bit. Shortly after had new threaded holes in the receiver and scope rails mounted, with much less torque this time. Used Brownells video on how to make a screw jig from flat stock instead of using the gizzie. Have fixed 3 other receivers for a buddy at the local gun shop and more than paid for the kit.
Great kit for 10/22(2014-07-14)
This kit made fixing stripped holes in a 10/22 receiver
a snap! Thanks Brownell's.
Simple to use. (2016-03-12)
I used the kit to repair a Ruger 10-22 with a stripped scope mount/receiver screw. I only fixed the damaged screw hole. (Hey, if it isn't broke, don't fix it) The Kit comes with 2 taps, one gizzy and a bunch of screws. Useless instructions. The tap with a point is the taper tap, and you use it for holes that go all-the-way through, and you use it to start all holes because you need the pointed end to initiate the holes. The bottom tap is the one with the blunt end. You would use it for holes that do not go completely through. Again, start with the pointed tap. The kit does not come with a handle, so I bought a cheap 3-piece kit from Harbor Freight for $7.00. I clamped my receiver in a padded vise, made it as level as I could, sprayed a bit of WD-40 on the tap and in the receiver screw hole, and turned it in by hand with the taper tap. Easy as pie. The Gizzy wasn't threaded, so I ran the taper tap through the small hole on the gizzy, and then threaded one of the screws in until it was about the same length as my factory scope mount screws. I didn't measure it (I should have). About a minute on my grinder, and I checked the fit of the screw using the scope mount and 10-22 receiver. Make sure the screws don't extend too far into the receiver, because the bolt with make contact with it. Overall, it's a pretty simple kit, and I don't have to ship the gun back to Ruger or take it to a gun smith. They include enough screws to repair a few dozen rifles. According to Ruger, don't use Loc tite on the 10-22. Evidently, it adds a bit of pressure, and is the cause of countless stripped receivers. Good luck.
Excellent!!(2017-04-06)
Purchased a 541S at the local gun shop,not realizing three of the four base holes were stripped until trying to mount a base..This kits bottoming tap and the included oversize screws(after shortening to length) saved the day..Worked perfect,worth every penny. Thanks Brownells!
Produktnr: 080719212 BROWNELLS OVERSIZE WEAVER .146" -48 SCREWS 12 PACK Tillverkarens produktnummer: W05-719-212050806018518 Något större i diameter än den vanliga 6-48 skruven för montering av kikarsiktesbas. De flesta hål som "förstörts" under borrning eller gängning kan lagas; bara gänga om till .146"-48 och installera. Inget behov av att borra om basen eller vapnet. Tack till Doug Knowt för hans tips. Klicka Här för gängtappar.
269SEK147269,00 kr
*
Levernastid ca. 14-21 dagar. Mer än 10 st. i centrallagret.
Produktnr: 080719000 BROWNELLS OVERSIZE .146 -48 SCREW SHOP KIT050806018495 Något större i diameter än den vanliga 6-48 skruven för montering av kikarsiktesbas. De flesta hål som "förstörts" under borrning eller gängning kan lagas; bara gänga om till .146"-48 och installera. Inget behov av att borra om basen eller vapnet. Tack till Doug Knowt för hans tips. Klicka Här för gängtappar.
1599SEK01 599,00 kr
*
Restorder. Skickas när den finns i lager. Leveranstid ca 4-12 veckor från centrallagret.
Skruvarna är något större i diameter än vanliga 6-48 skruvar, vilket gör det möjligt att laga "förstörda" hål utan att behöva borra om basen eller vapnet.
Kittet innehåller 48 skårade maskinskruvar i både Fillister- och Weaver-stil, samt förskärningstapp, bottentapp och en Screw Gizzie.
Blånerad finish och skruvarna mäter .146"-48x½" (12.7mm).
Produktnr: 080719112 BROWNELLS OVERSIZE FILLISTER .146 -48 SCREWS 12 PACK Tillverkarens produktnummer: 89165050806018501 Något större i diameter än den vanliga 6-48 skruven för montering av kikarsiktesbas. De flesta hål som "förstörts" under borrning eller gängning kan lagas; bara gänga om till .146"-48 och installera. Inget behov av att borra om basen eller vapnet. Tack till Doug Knowt för hans tips. Klicka Här för gängtappar.
289SEK0289,00 kr
*
Restorder. Skickas när den finns i lager. Leveranstid ca 4-12 veckor från centrallagret.
Skruvarna är något större i diameter än vanliga 6-48 skruvar, vilket möjliggör reparation av förstörda hål utan behov av att borra om basen eller vapnet.
Kittet innehåller 48 skårade maskinskruvar med blånerad finish i både Fillister- och Weaver-stil, samt nödvändiga gängtappar och en Screw Gizzie.
Perfekt för att laga hål som blivit förstörda under borrning eller gängning, tack vare möjligheten att gänga om till .146"-48.
Saves Your "Tail Feathers" If A Hole Gets Stripped
Slightly larger in diameter than the common 6-48 scope base mounting screw. Most holes "ruined" while drilling or tapping can be fixed; just retap to .146"-48 and install. No need to redrill base or gun. Thanks to Doug Knowt for his tip. Click Here for taps.
SPECS: .146"-48x½" (12.7mm) slotted machine screws, blued finish. Fillister and Weaver-style head. Kit contains 48 of each style, 1 taper tap, 1 bottom tap, and 1 Screw Gizzie in a bench box.
Mer...
Räddar dina "svansfjädrar" om ett hål blir stripat
Något större i diameter än den vanliga 6-48 skruven för montering av kikarsiktesbas. De flesta hål som "förstörts" under borrning eller gängning kan lagas; bara gänga om till .146"-48 och installera. Inget behov av att borra om basen eller vapnet. Tack till Doug Knowt för hans tips. Klicka Här för gängtappar.
SPECS: .146"-48x½" (12.7mm) skårad maskinskruv, blånerad finish. Fillister- och Weaver-stil huvud. Kittet innehåller 48 av varje stil, 1 förskärningstapp, 1 botten tapp, och 1 Screw Gizzie i en bänklåda.
Antal betyg: 7
Från brownells.com: 7
Medelbetyg: 4,9
Saves a job gone bad!(2010-09-05)
8-40 Torx screws into a Remington 1100 stripped out the receiver. These screws, combined with the .146"-48 tap worked perfectly! As noted in tips description by Mr. Doug Knowt, no need to re-drill. Just run the tap through, install the oversize screws, and your done! The screw heads were exact size as Torx, and the screws were plenty long enough to grind to fit any application. Thanks Brownell's! Thanks Mr. Knowt!
Just the ticket!(2016-07-01)
I used these in conjunction with the required tap to fix the scope base screw holes in a Remington 597 receiver. The screw holes were a bit oversized as it came from the factory with only .002" of thread engagement.
Excellent fix! - almost perfect(2018-06-14)
I used these in conjunction with the associated tapered tap to fix the scope base screw holes in a Remington 700 receiver. The front two screws from the factory were stripped and would just spin. I had to drive them down through the holes after removing the barrel. The tapered tap did its' job by hand. Used the tap and a 1/8" drill bit on a piece of O-1 steel to allow me to cut and file the screws down to size. The only issue with these screws is the slotted head. My Burris XTR steel scope base calls for 35 in lbs of torque and the little slotted screw head wouldn't hold the bit all of the way to 35 in lbs of torque. A socket head or torx head would do the trick and would have made this solution perfect. Very happy overall though, I recommend this solution for stripped receiver scope base holes.
Receiver saver!(2011-04-14)
This kit was great and easy to use. A friend and I purchased after both had stripped out screws on Ruger 10/22 receivers. Bought this kit and the proper drill bit. Shortly after had new threaded holes in the receiver and scope rails mounted, with much less torque this time. Used Brownells video on how to make a screw jig from flat stock instead of using the gizzie. Have fixed 3 other receivers for a buddy at the local gun shop and more than paid for the kit.
Great kit for 10/22(2014-07-14)
This kit made fixing stripped holes in a 10/22 receiver
a snap! Thanks Brownell's.
Simple to use. (2016-03-12)
I used the kit to repair a Ruger 10-22 with a stripped scope mount/receiver screw. I only fixed the damaged screw hole. (Hey, if it isn't broke, don't fix it) The Kit comes with 2 taps, one gizzy and a bunch of screws. Useless instructions. The tap with a point is the taper tap, and you use it for holes that go all-the-way through, and you use it to start all holes because you need the pointed end to initiate the holes. The bottom tap is the one with the blunt end. You would use it for holes that do not go completely through. Again, start with the pointed tap. The kit does not come with a handle, so I bought a cheap 3-piece kit from Harbor Freight for $7.00. I clamped my receiver in a padded vise, made it as level as I could, sprayed a bit of WD-40 on the tap and in the receiver screw hole, and turned it in by hand with the taper tap. Easy as pie. The Gizzy wasn't threaded, so I ran the taper tap through the small hole on the gizzy, and then threaded one of the screws in until it was about the same length as my factory scope mount screws. I didn't measure it (I should have). About a minute on my grinder, and I checked the fit of the screw using the scope mount and 10-22 receiver. Make sure the screws don't extend too far into the receiver, because the bolt with make contact with it. Overall, it's a pretty simple kit, and I don't have to ship the gun back to Ruger or take it to a gun smith. They include enough screws to repair a few dozen rifles. According to Ruger, don't use Loc tite on the 10-22. Evidently, it adds a bit of pressure, and is the cause of countless stripped receivers. Good luck.
Excellent!!(2017-04-06)
Purchased a 541S at the local gun shop,not realizing three of the four base holes were stripped until trying to mount a base..This kits bottoming tap and the included oversize screws(after shortening to length) saved the day..Worked perfect,worth every penny. Thanks Brownells!