(0) 
Nyhetsbrev
M1,
M14,
M1A
Springfield
Produktnr: 080000185
050806005679 Tjocka, stålhandtag ger den nödvändiga styrkan och styvheten för att dra åt och lossa flash suppressor-nut på M1A/M14 gevär. Härdade tänder ger exakt grepp för att eliminera notch stripping. Gummihylsor ger en positiv greppyta.Levernastid ca. 14-21 dagar.
CASTLE NUT PLIERS är det perfekta verktyget för att hantera flash suppressor-nut på M1A/M14 gevär. Med en robust konstruktion och högkvalitativa material erbjuder dessa tänger både styrka och precision.
Tjocka, stålhantag ger nödvändig styrka och styvhet för att både dra åt och lossa flash suppressor-nut på M1A/M14 gevär. Härdade käftspetsar säkerställer exakt grepp för att eliminera notch stripping. Gummihylsor ger en positiv greppyta.
M1,
M14,
M1A
Springfield
Works if you use correctly. 2018-05-06
I used these on a James River armory castle nut that was extremely tight and would not even come loose with the brass punch method and pb blaster. My rifle had the flash hider installed and then the steel face of the flashider that the castle nut tightens forward against was actually peened down against the castle nut then finished over. I assume James river armory does this to accurize the rifle. It was so tight I had to actually clamp my BAD T3 gas cylinder wrench (also purchased here) in a vise while attached to the m-14 gas cylinder and have the rifle resting in a gun cleaning cradle. I firmly grabbed the castle nut with these Brownell pliers and with both hands squeezed them tightly shut and also grabbed the top end of the pliers squeezing them shut here as well (right hand on the handles and left hand on the top squeezing both ends closed at the same time). At the same time, I was holding the pliers closed from both ends I was pushing them rearward tightly into the castle nut grooves so they could not slip or jump out of the grooves and shear the plier teeth or strip the grooves on the castle nut. It was an absolute monster to break loose, but it did so with no damage to pliers or castle nut. Also, again, my rifle was very securely held in place in a gun cradle with a gas cylinder wrench attached and the wrench hung downward from the rifle and secured in a 5" bench vise. There would have been no way to do this without this setup because of the amount of force needed to break this loose. A second person just holding the rifle by hand would have resulted in the rifle just spinning in this persons grasp. I cannot comment on other users who left low ratings without seeing the technique they used with the pliers, but with the amount of force I had to use on this tool I cannot see how it failed for other users unless they need to change up their technique a bit. If I would have just grabbed the pliers by the handles only and tried to twist the nut loose I believe they would have bent or broken. I hope this method helps other users. The reason I took away 1 star is because the handle covers do slip right off and I do believe this tool could be made of thicker steel which would make them live longer. I also used them to re-tighten the castle nut which required just as much torque to line up the Allen screw hole to the castle nut slot and with my same two-handed pushing technique it worked here as well too. As others have said, DO NOT forget to remove the castle nut set screw from the front sight base before removing the castle nut! I would not buy the cheaper version of this brownells sells because the cost savings is negligible.
Worked perfectly 2018-04-08
These pliers worked perfectly to remove and install the castle nut on my m1a. As others have stated don't forget the locking screw and use some penetrating oil when removing the nut.
Vi stötte på ett fel när vi laddade innehållet. Vänligen uppdatera sidan för att fortsätta. Om problemet kvarstår, kontakta vår kundtjänst.
till Brownells Sverige, din destination för allt vapenrelaterat. Med våra rötter i en genuin passion för skjutvapen, ger vi dig ett oöverträffat urval av vapendelar, skjutvapen tillbehör, vapensmedsverktyg, kikarsikten & rödpunktsikten och expertkunskap.
Oavsett om du vill underhålla, reparera eller uppgradera så har vi det du behöver!
För skyttar, av skyttar
Vi delar din entusiasm och vet exakt vad du letar efter eftersom vi är en del av gemenskapen.
Massivt urval
Från det väsentliga till det unika, hitta allt under ett tak.
Vår blandning av tradition och innovation
Handla med bekvämligheten av modern teknik, uppbackad av ett arv av erfarenhet.
Bläddra i vår samling och upptäck varför vi är det pålitliga namnet inom skyttesport och jakt.
© 2025 Brownells Sverige
Part of the Brownells Europe Group
Klassisk visning
Mobilvisning
Hjälp och kontakt
