It's easy to eliminate excess cylinder and yoke endplay with these stainless steel bearings. Made by pistolsmith Ron Power as an alternative to stretching the yoke. Whether rebuilding worn guns or building custom ones, these will help turn out a 1st-class job. Each pak contains 10 bearings of 1 thickness.
SPECS: Hardened 302 stainless steel. Cylinder Bearings - see chart. Yoke Bearings - .002" (.051mm) thick for S&W K,L,N.
Mer...
Kundernas betyg påPOWER CUSTOM PC-2 .002 (.051MM) THICK SMITH & WESSON K, L, N
Antal betyg: 2
Från brownells.com: 2
Medelbetyg: 5
Alternate use(2015-05-11)
I have used these on revolvers, but what I use them for more often is with action screws on bolt action rifles. instead of drilling down the screw recesses in a trigger guard or trimming the underside of the screw head, just put the proper number of these under the screw to align the screw slot with the long axis of the rifle. Much easier.
End Shake Shim(2017-01-07)
A few years back, I sent a revolver to S&W for excessive end shake. After big dollars to ship each way, the repair at S&W was $6.00. I later learned of these Power Custom Bearings....(end shake shims) Long story short, these shims work perfectly you just need to pay attention to the thread direction of the ejector rod/cylinder assembly. Some are left and some right depending on which dash your S&W is. Other that that, easy to install and saves huge dollars!
Produktnr: 713100002 POWER CUSTOM PC-2 .002 (.051MM) THICK SMITH & WESSON K, L, N Tillverkarens produktnummer: PC2 Det är lätt att eliminera överskott cylinder och oket endplay med dessa kullager av rostfritt stål. Som pistolsmith Ron Power som ett alternativ till stretching oket. Om återuppbyggnad av slitna kanoner eller bygga anpassade sådana, dessa kommer att hjälpa slå ut förstklassiga jobb. Varje pak innehåller 10 lager 1 tjocklek.
389SEK9389,00 kr
*
9 på lager
Funktioner:Make: Smith & WessonModell: K Frame, L Frame, N Frame
Make:
Smith & Wesson
Modell:
K Frame,L Frame,N Frame
Leveransvikt: 0,018kgHöjd: 13mmBredd: 114mmLängd: 114mm
Produkt detaljer
Tillverkas i USA
Produktnr: 713100004 POWER CUSTOM PC-4 .004 (.10MM) THICK SMITH & WESSON K, L, N Tillverkarens produktnummer: PC4 Det är lätt att eliminera överskott cylinder och oket endplay med dessa kullager av rostfritt stål. Som pistolsmith Ron Power som ett alternativ till stretching oket. Om återuppbyggnad av slitna kanoner eller bygga anpassade sådana, dessa kommer att hjälpa slå ut förstklassiga jobb. Varje pak innehåller 10 lager 1 tjocklek.
389SEK4389,00 kr
*
4 på lager
Funktioner:Make: Smith & WessonModell: K Frame, L Frame, N Frame
Produktnr: 713012002 POWER CUSTOM YOKE ENDSHAKE BEARINGS, SMITH & WESSON K, L, N ONLY Tillverkarens produktnummer: PY2 Det är lätt att eliminera överskott cylinder och oket endplay med dessa kullager av rostfritt stål. Som pistolsmith Ron Power som ett alternativ till stretching oket. Om återuppbyggnad av slitna kanoner eller bygga anpassade sådana, dessa kommer att hjälpa slå ut förstklassiga jobb. Varje pak innehåller 10 lager 1 tjocklek.
389SEK0389,00 kr
*
Produkten kan beställas som restorder.
Funktioner:Make: Smith & WessonModell: K Frame, L Frame, N Frame
Produktnr: 713100001 POWER CUSTOM PC-J2 .002 (.051MM) THICK SMITH & WESSON J CENTERFIRE Tillverkarens produktnummer: PCJ2 Det är lätt att eliminera överskott cylinder och oket endplay med dessa kullager av rostfritt stål. Som pistolsmith Ron Power som ett alternativ till stretching oket. Om återuppbyggnad av slitna kanoner eller bygga anpassade sådana, dessa kommer att hjälpa slå ut förstklassiga jobb. Varje pak innehåller 10 lager 1 tjocklek.
Produktnr: 713200002 POWER CUSTOM PC-R2 .002 (.051MM) THICK SEC SIX®, GP100®, REDHAWK® Tillverkarens produktnummer: PCR2 Det är lätt att eliminera överskott cylinder och oket endplay med dessa kullager av rostfritt stål. Som pistolsmith Ron Power som ett alternativ till stretching oket. Om återuppbyggnad av slitna kanoner eller bygga anpassade sådana, dessa kommer att hjälpa slå ut förstklassiga jobb. Varje pak innehåller 10 lager 1 tjocklek.
It's easy to eliminate excess cylinder and yoke endplay with these stainless steel bearings. Made by pistolsmith Ron Power as an alternative to stretching the yoke. Whether rebuilding worn guns or building custom ones, these will help turn out a 1st-class job. Each pak contains 10 bearings of 1 thickness.
SPECS: Hardened 302 stainless steel. Cylinder Bearings - see chart. Yoke Bearings - .002" (.051mm) thick for S&W K,L,N.
Mer...
Kundernas betyg påPOWER CUSTOM PC-2 .002 (.051MM) THICK SMITH & WESSON K, L, N
Antal betyg: 2
Från brownells.com: 2
Medelbetyg: 5
Alternate use(2015-05-11)
I have used these on revolvers, but what I use them for more often is with action screws on bolt action rifles. instead of drilling down the screw recesses in a trigger guard or trimming the underside of the screw head, just put the proper number of these under the screw to align the screw slot with the long axis of the rifle. Much easier.
End Shake Shim(2017-01-07)
A few years back, I sent a revolver to S&W for excessive end shake. After big dollars to ship each way, the repair at S&W was $6.00. I later learned of these Power Custom Bearings....(end shake shims) Long story short, these shims work perfectly you just need to pay attention to the thread direction of the ejector rod/cylinder assembly. Some are left and some right depending on which dash your S&W is. Other that that, easy to install and saves huge dollars!