Brownells Sverige - Komplett utbud av laddutrustningar, vapendelar, skyttetillbehör, kulor, hylsor och optik Sverige

EGW
RUGER AUTO VORTEX VIPER/VENOM SIGHT MOUNT

841370112951 296000668
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
899 899 1 SEK
Produktnr: 296000668
EGW RUGER AUTO VORTEX VIPER/VENOM SIGHT MOUNT
Tillverkarens produktnummer: 49321 841370112951 EGW rödpunktsikten är avsedda att installeras från vänster till höger (med mynningen framåt). Svansen har en progressiv avsmalning för att underlätta installationen. Ta helt enkelt bort det bakre sikte på ditt vapen och ersätt det med EGW-monteringen för att kunna montera ditt Vortex Viper/Venom, Burris FastFire eller Docter rödpunktsikte. Du kan när som helst ta bort monteringen och återmontera ditt bakre sikte. Monteringsmaterial ingår. Installationsinstruktioner Ta bort det bakre sikte* Installera EGW Sight Mount i svansen Dra åt ställskruven (om tillämpligt) Placera rödpunktsiktet på EGW Sight Mount (att lägga en liten bit papper mellan rödpunktsiktet och siktesmonteringen kommer att göra det lättare att ta bort och kommer att hålla Loctite borta från rödpunktsiktet.) Applicera blå Loctite på de medföljande monteringsskruvarna Dra åt monteringsskruvarna till 15in/lbs 2 knapphuvudskruvar - Medföljer för Vortex Viper och Venom sikten 2 Platt huvudskruvar - Medföljer för Burris FastFire och Docter sikten De skruvar som medföljer denna montering kräver en 5/64'' insexnyckel för installation. Modifiering av ditt vapen kan ogiltigförklara tillverkarens garanti. Denna produkt bör installeras och kontrolleras av en kvalificerad vapensmed. Inget ansvar uttrycks eller antyds för skada eller skada som kan uppstå till följd av felaktig installation eller användning av denna produkt.
899 SEK 4 899,00 kr *
Levernastid ca. 14-21 dagar.
4 st. i centrallagret.
Funktioner: Basantal: 1-Piece Färg: Svart Make: Ruger Material: Aluminum Modell: Mark III, Mark I, Mark II, P90, P89, P94, P95, 22/45, Mark IV, P85, P91, P93, P97 Stil: Tactical

Produktinformation

Antal Baser: 1-Piece Färg: Svart Make: Ruger Material: Aluminum Modell: 22/45,Mark I,Mark II,Mark III,Mark IV,P85,P89,P90,P91,P93,P94,P95,P97 Stil: Tactical Leveransvikt: 0,045kg Leveranshöjd: 25mm Leveransbredd: 76mm Leveranslängd: 140mm

Produkt detaljer

Tillverkas i USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Nyhetsbrev