Brownells Sverige - Komplett utbud av laddutrustningar, vapendelar, skyttetillbehör, kulor, hylsor och optik Sverige

EGW
S&W M&P SHIELD EZ VORTEX VIPER/VENOM SIGHT MOUNT

841370117567 296000652
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Does not work with M&P, M&P 2.0 or M&P 22.
899 899 1 SEK
Produktnr: 296000652
EGW S&W M&P SHIELD EZ VORTEX VIPER/VENOM SIGHT MOUNT
Tillverkarens produktnummer: 49292 841370117567 EGW rödpunktsikten är avsedda att installeras från vänster till höger (med mynningen vänd framåt). Svansen har en progressiv avsmalning för att underlätta installationen. Ta bort det bakre sikten på ditt vapen och ersätt det med EGW-fästet för att kunna montera ditt Vortex Viper/Venom, Burris FastFire eller Docter rödpunktsikte. Du kan när som helst ta bort fästet och sätta tillbaka ditt bakre sikte. Monteringsutrustning ingår. Installationsinstruktioner Ta bort det bakre sikten* Installera EGW Siktesfästet i svansen Dra åt ställskruven (om tillämpligt) Placera rödpunktsiktet på EGW Siktesfästet (att placera en liten bit papper mellan rödpunktsiktet och siktesfästet kommer att underlätta borttagning och kommer att hålla Loctite borta från rödpunktsiktet.) Applicera blå Loctite på de medföljande monteringsskruvarna Dra åt monteringsskruvarna till 15in/lbs 2 knapphuvudskruvar - Tillhandahålls för Vortex Viper och Venom sikten 2 platt huvudskruvar - Tillhandahålls för Burris FastFire och Docter sikten Skruvarna som medföljer detta fäste kräver en 5/64'' insexnyckel för installation. Modifiering av ditt vapen kan ogiltigförklara tillverkarens garanti. Denna produkt bör installeras och kontrolleras av en kvalificerad vapensmed. Inget ansvar uttrycks eller antyds för skador eller skador som kan uppstå på grund av felaktig installation eller användning av denna produkt. Fungerar inte med M&P, M&P 2.0 eller M&P 22.
899 SEK 2 899,00 kr *
Levernastid ca. 14-21 dagar.
2 st. i centrallagret.
Funktioner: Basantal: 1-Piece Färg: Svart Make: Smith & Wesson Material: Aluminum Modell: M&P380 Shield EZ 2.0, M&P9 Shield EZ Stil: Tactical

Produktinformation

Antal Baser: 1-Piece Färg: Svart Make: Smith & Wesson Material: Aluminum Modell: M&P380 Shield EZ 2.0,M&P9 Shield EZ Stil: Tactical Leveransvikt: 0,029kg Leveranshöjd: 25mm Leveransbredd: 79mm Leveranslängd: 133mm

Produkt detaljer

Tillverkas i USA



EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Does not work with M&P, M&P 2.0 or M&P 22.
Nyhetsbrev