EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This Mount does not fit: Smith & Wesson M&P C.O.R.E Series (Already optics ready) Smith & Wesson M&P Shield EZ .380 Smith & Wesson M&P .22 Compact Smith & Wesson SW9VE Smith & Wesson SW40VE
Perfekt fäste för Vortex Viper/Venom på din S&W M&P!
EGW:s rödpunktsikter är designade för att installeras från vänster till höger (med mynningen riktad framåt). Dovetailen har en progressiv avsmalning för att underlätta installationen. Ta helt enkelt bort bakre sikten på din pistol och ersätt den med EGW-fästet för att montera din Vortex Viper/Venom, Burris FastFire eller Docter rödpunktsikte. Du kan ta bort fästet och återinstallera din bakre sikte när som helst. Monteringsmaterial ingår.
Installationsanvisningar
- Ta bort den bakre sikten*
- Installera EGW Sight Mount i dovetailen
- Dra åt setskruven (om tillämpligt)
- Placera rödpunktsiktet på EGW Sight Mount (att lägga en liten bit papper mellan rödpunktsiktet och fästet underlättar borttagning och håller Loctite borta från rödpunktsiktet).
- Tillämpa blå Loctite på de medföljande monteringsskruvarna
- Åtdragning av monteringsskruvarna till 15in/lbs
Inkluderade skruvar:
- 2 Button Head Cap Screws - För Vortex Viper och Venom Sights
- 2 Flat Head Cap Screws - För Burris FastFire och Docter Sights
Skruvarna som ingår med detta fäste kräver en 5/64'' insexnyckel för installation.
Modifiering av ditt vapen kan ogiltigförklara tillverkarens garanti.
Denna produkt bör installeras och kontrolleras av en kvalificerad vapensmed.
Ingen ansvarighet uttrycks eller antyds för skador eller skador som kan uppstå från felaktig installation eller användning av denna produkt.
Detta fäste passar inte:
- Smith & Wesson M&P C.O.R.E Series (Redan optikredo)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson M&P .22 Compact
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE