OPF-G43x/48, RMRcc (Optics Platform, Forward Controls, G43x/48, RMRcc) is the latest member of the OPF line. G43x and 48 MOS slides are designed for direct mounting of the Shield RMSc sight. Trijicon's RMRcc is longer, and requires an adapter plate which also necessarily raises the mounting surface in order to mount an RMRcc. RMRcc has its own footprint. Gone are the two lug holes in front, these are replaced by two larger diameter threaded posts (bosses) through which the sight to mount/plate screws are installed. The sight to mount/plate screws are also significantly strengthened, though with the OPF-G, RMRcc design that holds the sight immobile on the plate, the larger diameter and stronger screws aren't as important, we always welcome screws that are less likely to strip. With the OPF-G43x/48, RMRcc, we didn't merely raise the mounting surface to provide a platform for the RMRcc. As RMRcc is longer than the G43X/48 MOS cut, the sight overhangs on the slide. When installed, the bottom of RMRcc (with Trijicon provided sealing plate installed) is almost flush with the top of the slide so the sight is as low as possible. We positioned the RMRcc towards the center of the plate as much as feasible, this is done to reduce the amount of unsupported overhang on the RMRcc's sealing plate in front. RMRcc has a rubber gasket around its battery compartment to keep water and moisture at bay, which pushes the sealing plate downward. This isn't an issue if the plate is of the same length as the RMRcc, but with an overhang, it creates a slight gap between the gasket and the sealing plate. OPF-G43x/48, RMRcc's design eliminates the gap/opening between the sight and sealer plate, to the point of emulating a plate that's as long as the sight itself. To wit, if the plate is as long as the RMRcc, it will make the installed height of RMRcc even taller, which is the very reason we chose to let the sight overhang. Torque value: Plate to slide: 12 to15 in·lbs. Sight to plate: 18 in·lbs.. Weight: 0.75oz Material: 1018 steel, black nitrided
Adapterplatta för Trijicon RMRcc på Glock 43/48 - Förbättra din sikteupplevelse!
OPF-G43x/48, RMRcc (Optics Platform, Forward Controls, G43x/48, RMRcc) är den senaste medlemmen i OPF-serien. G43x och 48 MOS-slides är designade för direkt montering av Shield RMSc-sikten. Trijicons RMRcc är längre och kräver en adapterplatta som också höjer monteringsytan för att kunna montera en RMRcc. RMRcc har sin egen fotavtryck.
De två lug-hålen fram har ersatts av två större gängade stift (bossar) genom vilka skruvarna för sikte till platta installeras. Skruvarna för sikte till platta är också betydligt förstärkta, men med OPF-G, RMRcc-designen som håller siktet stilla på plattan, är de större och starkare skruvarna inte lika viktiga. Vi välkomnar alltid skruvar som är mindre benägna att stripas.
Med OPF-G43x/48, RMRcc har vi inte bara höjt monteringsytan för att ge en plattform för RMRcc. Eftersom RMRcc är längre än G43X/48 MOS-skärningen, hänger siktet över på slidan. När det är installerat är botten av RMRcc (med Trijicon tillhandahållen tätplatta installerad) nästan i nivå med toppen av slidan, så att siktet är så lågt som möjligt.
Vi har positionerat RMRcc så centralt på plattan som möjligt för att minska mängden osupporterad överhäng på RMRcc:s tätplatta fram. RMRcc har en gummipackning runt batterifacket för att hålla vatten och fukt borta, vilket trycker tätplattan nedåt. Detta är inte ett problem om plattan är lika lång som RMRcc, men med ett överhäng skapas en liten lucka mellan packningen och tätplattan.
OPF-G43x/48, RMRcc:s design eliminerar luckan/öppningen mellan siktet och tätplattan, till den grad att den imiterar en platta som är lika lång som siktet självt. Om plattan är lika lång som RMRcc, kommer det att göra den installerade höjden av RMRcc ännu högre, vilket är anledningen till att vi valde att låta siktet hänga över.
- Momentvärde: Platta till slide: 12 till 15 in·lbs.
- Sikte till platta: 18 in·lbs.
- Vikt: 0.75 oz
- Material: 1018 stål, svart nitriderad