Produktinformation
- Modell:
L Frame
- Vapentyp:
Smith & Wesson
- Leveransvikt: 0,024kg
- Leveranshöjd: 5mm
- Leveransbredd: 102mm
- Leveranslängd: 109mm
Produkt detaljer
USA: s exportklassificering: 0A501.x
Produktnr: 713000168
Tillv.nr.: P-1-02
Fjäderbelastade, längre hammartoppar ger en konsekvent och positiv tändning med den lättaste hammartensionen, vilket möjliggör en lättare och smidigare funktion. Tillverkad med wire EDM och CNC precisionsfräsning, med kvalitetskontrollerad värmebehandling från S7 verktygsstål. Hammartopparna är maskinbearbetade, inte stämplade. Designad för att vara hållbar och ge en lång livslängd. Detta kit inkluderar hammartopp, fjäder och hammartoppnitar. Vanligtvis behövs bara en normal ersättning, även om vissa fabriksvariationer kan kräva mindre justeringar. Designad för Smith & Wesson centerfire modeller, K, L och N.Levernastid ca. 14-21 dagar.
Våra HAMMER NOSE KITS för Smith & Wesson L-ram är utformade för att ge en konsekvent och positiv tändning med minimal hammartension, vilket resulterar i en lättare och smidigare åtgärd.
Denna uppsättning innehåller hammarnäsa, fjäder och hammarnäsa nitar. Hammarnäsa kit är tillverkade med hjälp av wire EDM och CNC precisionsbearbetning, med kvalitetskontrollerad värmebehandling av S7 verktygsstål. Hammarnäsa är maskinbearbetade, inte stämplade, vilket gör dem hållbara och ger en lång livslängd.
Dessa kits är designade för Smith & Wesson centerfire-modeller och är det perfekta valet för den som söker högkvalitativa reservdelar för sina vapen.
L Frame
Smith & Wesson
it didn'work 2016-08-07
Installed in a mod 66-1 S&W. tried lighten DA trigger pull. Installation was easy,no problems. Test fired ,3 misfires out of 6 DA, 1 out of 6 SA. Tried factory ammo,same results. Removed new firing pin,measured and compared with old,and no differences. Reinstalled old firing pin,no further problems. First time Power Custom has let me down.
Misfire problem solved. 2015-11-02
I have a recently acquired nearly unfired 1971 vintage model 19-3 that was misfiring (1 in 6) with 357 Magnum ammunition featuring CCI 550 primers, even when the DA trigger weight was increased to 10 lbs using a primer cup on the strain screw. Checking the hammer nose projection showed it was about 0.02 inch short of the thickness of a Dime. So, the obvious conclusion is that the Bangor Punta vintage hammer nose was just a bit short.
Since parts for these older models can be difficult to find I decided to try the Power Custom hammer nose for a post 1988 lockwork. The new hammer nose dropped right in and needed no fitting at all. The projection is a bit on the heavy side, about 0.06 inch per my calibrated eyeball but a 150 round test in both double and single action showed no indication at all of an overstruck primer and there were zero misfires in that test.
Kudo's to Power Custom for the instruction/guidance that was packaged with the kit. While I didn't need to do any fitting it was nice to see they provided clear illustrations of the fitting points. It was also helpful to see clear instructions on how it should function and how to test for correct function.
Based on my single sample test I think it is actually fairly safe to assume that this particular hammer nose will fit K frame hammers from 1971 to later vintages. I also think that the tensioning spring will act to protect the hammer nose a bit when compared to the older version.
Vi stötte på ett fel när vi laddade innehållet. Vänligen uppdatera sidan för att fortsätta. Om problemet kvarstår, kontakta vår kundtjänst.