Varukorgen är tom.

Varukorg

0247-41085

Prenumerera på nyhetsbrev

TRIPLE-K
REMINGTON 7400 10RD MAGAZINE 30-06 SPRINGFIELD

730745000491 486000002

More Rounds Than Factory Magazine All-Steel Body Gives Rigidity

Durable high-capacity magazine provides a long service life and holds ten rounds for fewer reloads when shooting your Remington 740, 742, 750, or 7400. Folding, leaf spring and nylon follower ensure reliable feeding. Available in .30-06 and .308.

SPECS: Steel, blued. Approximately 31⁄2" (9cm) wide, 37⁄16" (8.7cm) high, 1" (2.54cm) thick. Fits Remington 740, 742, 750 & 7400.

Mer...

Fler Skott Än Fabriksmagasinet Stålkropp Ger Stabilitet

Hållbart magasin med hög kapacitet som ger en lång livslängd och rymmer tio skott för färre omladdningar när du skjuter med din Remington 740, 742, 750 eller 7400. Vikbar, bladfjäder och nylonföljare garanterar pålitlig matning. Finns tillgänglig i .30-06 och .308.

SPECS: Stål, blånerat. Ungefär 31⁄2" (9 cm) brett, 37⁄16" (8,7 cm) högt, 1" (2,54 cm) tjockt. Passar till Remington 740, 742, 750 & 7400.

Mer...

Kundernas betyg påTRIPLE-K REMINGTON 7400/742 MAGAZINE 30-06 SPRINGFIELD 10RD STEEL BLA

Antal betyg: 16
Från brownells.com: 16
Medelbetyg: 2,9

does the job (2010-04-21)

bought for my rem750 in .270 win. ammo loads well, mag fits like a dream and no problems with jams, ftf, etc up to this point.
numbers don't lie, 10>4, hope to be using these for a while

Awesome Purchase (2010-06-22)

This is an awesome addition to my Model 742 and let me tell you, I feel much more comftorable in the woods hunting hogs than with the stock 4 round clip. I fired off 20 rounds in each of the two clips that I purchased and both fired and loaded flawlessly. The one draw back is that I have to hold the action open when I insert the clip in order for it to be fully inserted. Not a big deal for me and I would buy this product again and again.

Works well in 7600 (2010-07-10)

The lack of bolt hold open is a non-issue in the Remington 7600. My particular magazine had a rough start with some extra metal that caught on case mouths as they were fed, but 30 seconds with a Dremmel tool solved that nicely. I traced the contour from the front of a factory mag onto this one and ground to match. Too bad Triple-K didn't do the same at the factory. After cleaning up the front of the magazine I've had no further problems. The spring holds tension well when left loaded. My example has remained loaded for the last 6 years and still feeds rounds as fast as I can shuck the action.

979M REM 7400 10rd magazine (2011-05-28)

I was glad of purchase I made from Italy, so that my friends who have also a Remington 7400 luxury carbine .30-06 I prayed for them to buy the magazine from 10 shots.

Not perfect. (2011-09-12)

I bought 2 of these for my remington 7400 to use at the gun range, the quality is ok but not as good as factory. It needs a little manhandling to get it fully seated into the rifle. I would've like to seen all metal used in the construction (the follower is plastic and has alot of play front to back) The biggest problem I have with it is that it holds the bullets down too long and they mash into the bottom of the feed ramp causing a jam and deformed bullit tips.

Triple K Version is generally good (2011-11-27)

I use it in my 742, 30-06. I initially found that it bound my bolt.
I needed to take it to the grinding wheel (Dremmel) to match my original Remington clip. A few strokes with the grinder and now it feeds properly.

I would recommend it.

not again (2012-01-19)

bought 2 for 742 30-06, fowler poped out, no front tabs to hold fowler in, sides misscut,
sides not bent in at a proper curve to hold rounds, not worth the postage to return to triple k

Good buy. (2012-06-29)

Good buy. ran 50 rounds through it in one session, no misfeeds, worked like a champ.

will not chamber 3 rounds in a row. (2012-10-03)

I have cleaned my rifle, also cleaned both of my 4 and 10 round mags. My rifle shot fine with the 4 round mag, but it would not shoot 3 times in a row with the 10 round mag. It even broke to tip off of 1 of my Ballistic Tip bulletswith the 10 round mag in, the action feels slower like it is dragging. Putting both clips aft end towards each other you can see the original mag is a mil or 2 wider at the feed point. Perhaps thats the problem? Maybe it can be bent?

Poor Quality Magazines (2014-09-16)

Recently bought two of these 10 round magazines for my 30-06.

I first time I put the rounds into one of them,the bottom cap came off, the spring flew out and the rounds ended up on the turf. Was pretty embarrassed at the range..The other magazine that does work is exceptionally tight fitting and difficult to get out of the gun..Not happy at all about this purchase

Tony Magazzi

7400 rifle (2014-11-11)

Bought this for a REM 7400 the clip holds the shell down to long and jams every time. The indents on the side of the clip that raise the bullet is to far forward about a 3/16 in. compared to the clip I use a 280. Might work with bullets that have a very short nose on them or other models.

Very reliable (2016-02-11)

I had a very hard time finding spare or aftermarket magazines for my 7400, either standard or high capacity. It can be a pain at the range to constantly stop shooting and reloading a single four round magazine. It's hard to relax and enjoy what you're doing when you need to constantly stop and reset everything. I was happy to finally find one at Brownells. I ordered two of the ten round magazines, and I love them both. They both work perfectly, and they fit and function more smoothly than the original. Reading the other reviews, it seems that people either love them or hate them. It could be that they have some quality control issues, and I might have caught them on a good day. It's possible they only work well in the 7400 / 7600 models, or maybe just in mine. All I can offer an opinion on are the ones I received, and I'm firmly in the "love them" group. I'll be ordering a couple more as soon as they're back in stock.

Doesn't worn in Model 742 (2016-07-28)

These mags don't load, seat & cause the bolt to jam in Remington Model 742. None of the 7400 series mags seem to fit, load or properly operate either. Keep looking for actual Remington 742 mags otherwise you're just waisting time & money.

Trash (2018-03-01)

The bolt won't cycle if there's more than one round in the mag, won't take more than 5 rounds, the mag takes a lot of force to go into the well which means it doesn't fit.. Also, there's no bolt release on it. I don't know whether to return them or just throw them away because I know it's my civic duty.

Puts bullets in my gun (2018-03-09)

Shipping was a little on the slower side for standard shipping but I was in no rush to get it anyway but it does what a clip is supposed to I put it in my gun and it gave my gun bullets with no jams so there is nothing to complain about

Not bad but needs improvement (2018-08-12)

I had purchased mine and was stoked to get it but first day at the range and it jammed on every round. I did figure out why, it seems the indents in the side of it were to far forward to assist the round into the feed ramps on my 7400, I was able to get some durable epoxy to stick and made a spot on each side to assist the rounds. The quality seems pretty good, put together well just the slight tweaks and it would be a 5 star. Other then the slight issue it works pretty good and fits pretty well but hope who ever makes them can see these and make the proper improvements to make it a great magazine.

Läs 16 fler betyg på brownells.com

599 599 1 SEK

Produktnr: 486000002
TRIPLE-K REMINGTON 7400/742 MAGAZINE 30-06 SPRINGFIELD 10RD STEEL BLA
Tillverkarens produktnummer: 979M 730745000491 Hållbart magasin med hög kapacitet som ger en lång livslängd och rymmer tio skott för färre omladdningar när du skjuter med din Remington 740, 742, 750 eller 7400. Vikbar, bladfjäder och nylonföljare garanterar pålitlig matning. Finns tillgänglig i .30-06 och .308.

599 SEK 179 599,00 kr *

Levernastid ca. 14-21 dagar.
Mer än 10 st. i centrallagret.

Funktioner: Action Type: Semi-Auto Finish: Svart Kapacitet: 10-Round Make: Remington Material: Stål Modell: 7400 Patron: 30-06 Springfield Mängd: 1

Lägg till i inköpslista

Fråga om produkt

Information

Lägg till i inköpslista

Fråga om produkt

Produktinformation

Action Type: Semi-Auto Finish: Svart Kapacitet: 10-Round Make: Remington Material: Stål Modell: 7400 Patron: 30-06 Springfield Leveransvikt: 0,159kg Leveranshöjd: 38mm Leveransbredd: 114mm Leveranslängd: 180mm

Produkt detaljer

Tillverkas i USA
USA: s exportklassificering: 0A501.x

More Rounds Than Factory Magazine All-Steel Body Gives Rigidity

SPECS: Steel, blued. Approximately 31⁄2" (9cm) wide, 37⁄16" (8.7cm) high, 1" (2.54cm) thick. Fits Remington 740, 742, 750 & 7400.

Mer...

Fler Skott Än Fabriksmagasinet Stålkropp Ger Stabilitet

SPECS: Stål, blånerat. Ungefär 31⁄2" (9 cm) brett, 37⁄16" (8,7 cm) högt, 1" (2,54 cm) tjockt. Passar till Remington 740, 742, 750 & 7400.

Mer...

Kundernas betyg påTRIPLE-K REMINGTON 7400/742 MAGAZINE 30-06 SPRINGFIELD 10RD STEEL BLA

Antal betyg: 16
Från brownells.com: 16
Medelbetyg: 2,9

does the job (2010-04-21)

bought for my rem750 in .270 win. ammo loads well, mag fits like a dream and no problems with jams, ftf, etc up to this point.
numbers don't lie, 10>4, hope to be using these for a while

Awesome Purchase (2010-06-22)

Works well in 7600 (2010-07-10)

979M REM 7400 10rd magazine (2011-05-28)

I was glad of purchase I made from Italy, so that my friends who have also a Remington 7400 luxury carbine .30-06 I prayed for them to buy the magazine from 10 shots.

Not perfect. (2011-09-12)

Triple K Version is generally good (2011-11-27)

not again (2012-01-19)

bought 2 for 742 30-06, fowler poped out, no front tabs to hold fowler in, sides misscut,
sides not bent in at a proper curve to hold rounds, not worth the postage to return to triple k

Good buy. (2012-06-29)

Good buy. ran 50 rounds through it in one session, no misfeeds, worked like a champ.

will not chamber 3 rounds in a row. (2012-10-03)

Poor Quality Magazines (2014-09-16)

7400 rifle (2014-11-11)

Very reliable (2016-02-11)

Doesn't worn in Model 742 (2016-07-28)

Trash (2018-03-01)

Puts bullets in my gun (2018-03-09)

Not bad but needs improvement (2018-08-12)

Läs 16 fler betyg på brownells.com

Kunder har även köpt

SPEEDLOADER - HKS CA-44 FITS .44 SPEC., 5-SHOT S&W 696, TAURUS, ROSSI

HKS CA-44 FITS .44 SPEC., 5-SHOT S&W 696, TAURUS, ROSSI
SPEEDLOADER

HKS

Lagervara

279,00 kr * 269,00 kr - 289,00 kr*

Cylinder Snabbladdare

4,5

LEE PRECISION LEE LENGTH GAUGE/ SHELLHOLDER, 7MM REM MAG
CASE LENGTH GAUGES

LEE PRECISION

Lagervara

159,00 kr * 139,00 kr - 199,00 kr*

Svarv Hylshållare | Svarv tillbehör

REMINGTON 740, 760/ITHACA 37 SCOPE BASES - EGW REM 740, 742, 760/ITHACA 37 0 MOA

EGW REM 740, 742, 760/ITHACA 37 0 MOA
REMINGTON 740, 760/ITHACA 37 SCOPE BASES

EGW

Lagervara

599,00 kr *

Gevär Baser

REMINGTON 4, 6, 7400 SCOPE BASES - EGW REMINGTON 4, 6, 7400, 750, 7600, 7615 0 MOA

EGW REMINGTON 4, 6, 7400, 750, 7600, 7615 0 MOA
REMINGTON 4, 6, 7400 SCOPE BASES

EGW

Lagervara

599,00 kr *

Gevär Baser

ADVANCED TECHNOLOGY REMINGTON 7600 STOCK ADJUSTABLE BLACK
REMINGTON 7600 STOCK ADJUSTABLE

ADVANCED TECHNOLOGY

Lagervara

1 549,00 kr *

Bakkolvar

Logga in

Har du glömt lösenordet?
Registrering

SOCIAL MEDIA

Facebook

HEMSIDA

PRODUKTKATEGORI

BESTÄLLNING

KUNDSERVICE

Välkommen!

Välkommen till brownells.se, den ledande leverantören av skyttetillbehör, unika vapendelar, vapenrelaterade produkter, laddutrustningar, laddverktyg, kulor & hylsor, optik & vapensmide samt andra produkter för att underhålla, reparera och uppgradera dina vapen! Du kommer att hitta över 90.000 produkter till bra priser, stor lagerhållning samt brett utbud!

Vårt erbjudande:

Gillar du att skjuta, är vapensmed eller jägare, är detta platsen för dig! Skyttar, professionella vapensmeder, hobbyanvändare, militär/polis och pistolanvändare vänder sig till brownells.se för att hitta vapendelar och produkter av hög kvalitet.

cf-web-badges-e-ltgray