Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780 Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR This mount will fit: Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact* Smith & Wesson M&P 2.0 Compact* Smith & Wesson SD9VE Smith & Wesson SD40VE This mount does not fit: Smith & Wesson M&P Shield (Our mount is too wide to fit the Shield) Smith & Wesson M&P Shield EZ .380 Smith & Wesson SW9VE Smith & Wesson SW40VE Smith & Wesson M&P C.O.R.E Series *Will not fit the M&P .22 Compact. Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering.These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended*
Kompakt och hållbar monteringslösning för din Trijicon RMR
EGW:s S&W M&P TRIJICON RMR SIGHT MOUNT är designad för att ge en säker och stabil plattform för din Trijicon RMR rödpunktsikte. Tillverkad av högkvalitativ 7075 aluminium och med en matt svart hård yta, passar denna monteringsplatta perfekt för flera Smith & Wesson M&P-modeller.
Produktinformation
- Material: 7075 Aluminium
- Beläggning: Matt svart hårdcoating
- Övergripande längd: 1.780"
- Övergripande bredd: 1.1"
- Monteringshårdvara: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw
- Rödpunktskompatibilitet: Trijicon RMR
Denna monteringsplatta passar:
- Smith & Wesson M&P Full Size
- Smith & Wesson M&P 2.0 Full Size
- Smith & Wesson M&P 22 Full Size
- Smith & Wesson M&P Compact*
- Smith & Wesson M&P 2.0 Compact*
- Smith & Wesson SD9VE
- Smith & Wesson SD40VE
Denna monteringsplatta passar inte:
- Smith & Wesson M&P Shield (vår monteringsplatta är för bred för att passa Shield)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE
- Smith & Wesson M&P C.O.R.E Series
*Passar inte M&P .22 Compact. Smith & Wessons bakre siktesdovetail kan variera i dimensioner. Våra sikten är tillverkade enligt samma toleranser. Vissa användare kan ha problem med att installera vår platta på sin skena på grund av de varierande toleranserna i sina skenor. Tänk på detta när du beställer.
Installation: Dessa monteringar bör installeras och kontrolleras av en kvalificerad vapensmed. Ingen ansvarighet uttrycks eller antyds för skador eller skador som kan uppstå från felaktig installation eller användning av denna produkt.
För att installera, ta helt enkelt bort det bakre siktet på din pistol och ersätt det med vår monteringsplatta för att montera ditt Trijicon RMR rödpunktsikte. Inga ändringar krävs. Du kan ta bort vår monteringsplatta och ersätta ditt bakre siktet när som helst. Monteringshårdvara ingår.
Installationsinstruktioner
- Ta bort det bakre siktet*
- Installera EGW Sight Mount i dovetailen
- Dra åt set screw (om tillämpligt)
- Placera rödpunktsiktet på EGW Sight Mount (att placera en liten bit papper mellan rödpunktsiktet och monteringsplattan gör det enklare att ta bort och håller Loctite borta från rödpunktsiktet).
- Tillämpa blå Loctite på de medföljande monteringsskruvarna
- Dra åt monteringsskruvarna till 15in/lbs
*Bakre siktpushverktyg rekommenderas starkt