Brownells Sverige - Komplett utbud av laddutrustningar, vapendelar, skyttetillbehör, kulor, hylsor och optik Sverige
817953028452 100040941
The Geissele Suppressor Alignment Gage (SAG) is a precision gage used to verify the alignment of a suppressor to the bore of a firearm barrel. It is important to understand that the length of the suppressor is usually much longer than the length of the barrel / muzzle device / suppressor interface geometry. A small deviation at the mounting interface means a much larger deviation of the suppressor exit hole. The deviations from nominal can also be additive which compounds suppressor misalignment. The Geissele SAG is manufactured from hardened steel that has been ground 0.002” under nominal bore diameter. The outside diameter of the SAG is finely finished and straight to 0.001” over its length. Geissele hardens the SAG so that it will not wear by sliding exposure to abrasive powder residue, pull burrs if it slides against misaligned baffles nor allow abrasive particle to imbed into the surface of the gage. There can be a wide variation in barrel bore diameters and bore straightness. 0.002” under nominal bore diameter has been found to be the best size of the SAG that will fit most barrels. The long length of the SAG aligns the gage to the bore; it is not necessary to have a very tight fitting gage with the long length of the Geissele SAG.
1399 1399 1 SEK
Produktnr: 100040941
GEISSELE AUTOMATICS 9MM SUPPRESSOR ALIGNMENT GAGE
Tillverkarens produktnummer: 10-451-F 817953028452 Geissele Suppressor Alignment Gage (SAG) är ett precisionsverktyg som används för att verifiera att en ljuddämpare är korrekt justerad i förhållande till eldrörets axel på ett skjutvapen. Det är viktigt att förstå att ljuddämparens längd vanligtvis är mycket längre än längden på eldröret / mynningsanordningen / ljuddämparens gränssnittsgeometri. En liten avvikelse vid monteringsgränssnittet innebär en mycket större avvikelse vid ljuddämparens utloppshål. Avvikelser från nominella värden kan också vara additiva, vilket förvärrar missjusteringen av ljuddämparen. Geissele SAG är tillverkad av härdat stål som har slipats 0,002 tum under nominell kaliberdiameter. SAG:ens ytterdiameter är fint avslutad och rak till 0,001 tum över dess längd. Geissele härdar SAG så att den inte slits genom glidande exponering för slipande krutrester, inte drar upp borrar om den glider mot missjusterade bafflar och inte tillåter att slipande partiklar bäddar in sig i gageytan. Det kan vara stora variationer i eldrörets kaliberdiameter och rakhet. 0,002 tum under nominell kaliberdiameter har visat sig vara den bästa storleken på SAG som passar de flesta eldrör. SAG:ens långa längd gör att verktyget justeras efter eldröret; det är inte nödvändigt med ett mycket tätt passande verktyg med tanke på Geissele SAG:ens långa längd.
1399 SEK 21 1 399,00 kr *
Levernastid ca. 14-21 dagar.
Mer än 10 st. i centrallagret.

Produktinformation

Leveransvikt: 0,218kg Leveranshöjd: 1mm Leveransbredd: 13mm Leveranslängd: 432mm

Produkt detaljer

Tillverkas i USA



The Geissele Suppressor Alignment Gage (SAG) is a precision gage used to verify the alignment of a suppressor to the bore of a firearm barrel. It is important to understand that the length of the suppressor is usually much longer than the length of the barrel / muzzle device / suppressor interface geometry. A small deviation at the mounting interface means a much larger deviation of the suppressor exit hole. The deviations from nominal can also be additive which compounds suppressor misalignment. The Geissele SAG is manufactured from hardened steel that has been ground 0.002” under nominal bore diameter. The outside diameter of the SAG is finely finished and straight to 0.001” over its length. Geissele hardens the SAG so that it will not wear by sliding exposure to abrasive powder residue, pull burrs if it slides against misaligned baffles nor allow abrasive particle to imbed into the surface of the gage. There can be a wide variation in barrel bore diameters and bore straightness. 0.002” under nominal bore diameter has been found to be the best size of the SAG that will fit most barrels. The long length of the SAG aligns the gage to the bore; it is not necessary to have a very tight fitting gage with the long length of the Geissele SAG.
Nyhetsbrev